Panasonic VF200 Скачать руководство пользователя страница 263

Страница: 263 / 289

Appendix Function Parameter List

256

P143

Cooling Fan ON-OFF Control Select

・

Operation modes of cooling fan in normal status and fault status can be set.

Details

Setting

value

Operation of cooling fan

Operation when heat sink

is faulty

Power-on: ON

Power-off :OFF

The inverter stops

abnormally.

Power-on: ON

Heat sink temperature is

below 100

℃

: OFF

The inverter stops

abnormally.

Power-on: ON

Power-off :OFF

The inverter does not stop

but sends out alarm.

Power-on: ON

Heat sink temperature is

below 100

℃

: OFF

The inverter does not stop

but sends out alarm.

・

The parameter is invalid to models without cooling fan (1-phase 200 V/ 0.2 to

0.75 kW model and 3-phase 400 V/0.75 kW model).

P144

Input Terminal Filter

Filter constant of control circuit terminals (No.2 to No.8) can be set in the

inverter to effectively remove interference of external signal input.

Setting value (times)

5 to 100 (Increment = 1)

・

If the setting value is too high, the interference resistance capability will be

enhanced, but response speed of control input terminals will decrease.

・

If the setting value is too low, the interference resistance capability will be

weakened, but response speed of control input terminals will increase.

・

When start/stop, forward run and reverse run signal (terminal No.2 and No.3)

are used to operate the inverter, internal processing time of the inverter will

become longer even if the setting value is low. In this case, response speed of

control input terminals will be slower than other terminals.

Содержание VF200


































































































































































































































































































Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды

Panasonic VF200, Инструкция по эксплуатации

Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды