Panasonic VF200 Скачать руководство пользователя страница 31

Страница: 31 / 289

2. Installation

■

Connect the operation panel via a LAN cable

A commercially available LAN cable can be used to connect the main unit of
the inverter and the operation panel.

Use LAN cable only for the purpose of connecting the main unit of the inverter
and operation panel. Otherwise, the inverter could be damaged.

Specification for LAN cable: 8-Pin straight cable of CAT5 or higher (maximum
length is 5 m)

1. Cut off the power and then remove the panel following above instructions.

2. Insert one end of LAN cable to the main unit of the inverter and the other end

to connector (RJ45) on the panel until a “click” sound is heard.

■

Inverter side

■

Operation panel side

■

Installed on the plate (panel)

■

Mounting Procedure

1. Cut the mounting plate to above dimensions.

The suitable thickness of the plate is 1.0 mm ~ 3.5 mm.

2. Mount the operation panel onto the front side of plate (panel), and attach the

mounting screws supplied onto the rear side.(Tightening torque: 0.6 N

・

3. Mount LAN cable after the operation panel is installed.

Содержание VF200


































































































































































































































































































Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды

Panasonic VF200, Инструкция по эксплуатации

Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды