Antaira Technologies
IMP-C1000-SFP-bt-24 Series
Industrial Gigabit IEEE 802.3bt Ethernet-to-Fiber Media
Converter, 1*10/100/1000Tx RJ45 (90W/Port) to 1*100/1000 SFP
Slot; 12~55VDC Power Input
Quick Installation Guide
Version 1.0
(April 2020)
Tel: 1-844-268-2472
Fax: 1-714-671-9944
www.antaira.com
19020000000131
Package Check List
The package contains the following items:
Quick Installation Guide
IMP-C1000-SFP-bt-24(-T)
Wall mounting bracket set with screws
DC cable
–18 AWG & DC jack 5.5x2.1mm
Front Panel Layout
Top Panel View
IMP-C1000-SFP-bt-24 series top panel is equipped with one
4-pin removal terminal block connector for dual DC power inputs
(12~55VDC).
Product Overview
System Interface/Performance
RJ45 port support the auto MDI/MDI-X function
Ethernet RJ45 port connectivity 1*10/100/1000Tx (w/PSE:
90W/port)
Fiber connectivity with 1*100/1000Fx SFP slot
Store-and-forward switching architecture
Supports 10Kbytes Jumbo Frame
Power Input & Connection
DC 12~55VDC redundant power, with a 4-pin removal
terminal block
Max. current: 7A
Max. PoE output: 90W
It is recommended to using UL listed Industrial Power
Supply
Operating Temperature
Standard operating temperature model: -10°C ~ 65°C
Extended operating temperature model (
–T): -40°C ~ 75°C
Case/Installation
IP30 protection
DIN-Rail and wall mount design
Safety Precaution
If the DC voltage is supplied by an external circuit, please use a
protection device on the power supply input.
LED Indicators
LED
Color
Description
Power
Green
On
Power input 1 or 2 is active
Off
Power input 1 and 2 are inactive
AT PoE
Green
On
IEEE 802.3af/at connection
Off
No powered-device attached or power supplying fails
BT PoE
Blue
On
IEEE 802.3bt connection
Flashing
1. PoE over current or cable short
2. Invalid connection check signature or connection-
check error is detected
Off
No powered-device attached or power supplying fails
RJ45 Port
(Upper LED)
Green
On
Linked to network at 1000Mbps
Flashing
Networking is active
Off
Not connected to network
RJ45 Port
(Lower LED)
Green
On
Linked to network at 10/100Mbps
Flashing
Networking is active
Off
Not connected to network
SFP Port
Link/Act
Green
On
Connected to network, 100/1000Mbps
Flashing
Networking is active
Off
Not connected to network
DIP-Switching Setting
There are 3
sets of DIP
‐
switches on the front panel that are
responsible for the settings of PRRT (PD Remote Reset
Technology) function, LFP (Link Fault Pass) function, and SFP
transmission rate.
DIP-Switch Number
ON
OFF
1
PRRT Enabled
PRRT Disabled
2
LFP Enabled
LFP Disabled
3
SFP 100Fx
SFP 1000Fx
Note: After any DIP switch changes have been made, it is
required to power cycle the unit for the changes to take
effect.
Quick Installation
Ethernet RJ45 Port (Auto MDI/MDIX)
RJ-45 port is auto-sensing for 10Base-T, 100Base-TX or
1000Base-TX devices connections. Please follow the wiring pin
assignment table below for Ethernet port installation.
RJ45 Ethernet Port Pin Outs
Pins
T568A Color
T568B Color
10/100
Base-T(X)
1000
Base-T
PoE
1
White/Green
White/Orange
Rx+
TP0+
DC+
2
Green
Orange
Rx-
TP0-
DC+
3
White/Orange
White/Green
Tx+
TP1+
DC-
4
Blue
Blue
unused
TP2+
5
White/Blue
White/Blue
unused
TP2-
4-Pin Removal Terminal Block (Power Input)
100/1000Fx SFP slot
Grounding Screw
DIP Switch
LED for RJ45 Link/Activity
1000Mbps
LED for Power, at PoE, and bt PoE
10/100/1000TX RJ45 port
LED for SFP Link/Activity
LED for RJ45 Link/Activity
10/100Mbps
