Omron CRT1 - 10-2008 Скачать руководство пользователя страница 95

Страница: 95 / 584

Connecting Cables and Terminating Resistor

Section 3-4

Note

Before connecting the cable wires to the Terminating Resistor, first attach the
M3 crimp terminals shown below to the wires.

Round Cable II

Attach a DCN4-TM4 Terminating Resistor to the DCN4-TR4 Flat Connector
Socket connected to the cable.

Connection Method

Push in the Terminating Resistor until it clicks into place.

Note

To remove a Terminating Resistor once it has been connected, press in on the
latches on both sides and pull it out.

Flat Cable I

Attach a DCN5-TM4 Terminating Resistor to the DCN5-TR4 Flat Connector
Socket connected to Communications Cable.

Installation Method

Push in the Terminating Resistor until it clicks into place.

Note

To remove a Terminating Resistor once it has been connected,
press in on the latches on both sides and pull it out.

BDL (white) or BDH (black)

BDH (black) or BDL (white)

Round cable I

Terminating Resistor

6.0 mm max.

Flat Connector Socket

Round cable II

Terminating Resistor

Flat Connector Socket

Terminating
Resistor

Содержание CRT1 - 10-2008









































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CRT1 - 10-2008

Отзывы:

Похожие инструкции для CRT1 - 10-2008

Бренды по названию

Популярные бренды

Omron CRT1 - 10-2008, Руководство по эксплуатации

Результаты поиска

Содержание CRT1 - 10-2008

Отзывы:

Похожие инструкции для CRT1 - 10-2008

Бренды по названию

Популярные бренды