Omron CRT1 - 10-2008 Скачать руководство пользователя страница 503 | Manualshive

Страница: 503 / 584

background image

480

Temperature Input Unit Functions

Section 11-5

Connecting the Devices
Required for Adjustment

The following paragraphs explain how to connect the devices that must be
connected to the CRT1-TS04T for user adjustment. Wire the following devices
properly when adjusting the CRT1-TS04T.

■

Reference Voltage/Current Generator and Precision Digital Multimeter

Used to make adjustments at the upper limit and lower limit.

Prepare devices that can generate accurate 0 mV, 20 mV, and 50 mV volt-
ages. Use a precision digital multimeter that can measure the output voltage
and indicate when the voltage/current generator is not producing an accurate
voltage output.

■

Cold Junction Compensator (such as a ZERO-CON 0

°

C Bath) and

Compensating Conductors

Used to adjust the bias compensation value.

The cold junction compensator (the ZERO-CON 0

°

C bath is used in following

examples) is a device that maintains an accurate 0

°

C (32

°

F) temperature for

thermocouple sensors. Use a cold junction compensator compatible with the
sensor being adjusted.

Note

When using an R, S, E, B, or W type thermocouple, a K type can be substi-
tuted. Set the ZERO-CON to 0

°

C (32

°

F).

■

CX-Integrator

Actual adjustments are made from the CX-Integrator windows.

Adjustment Device Connection Diagram

Connect the reference voltage/current generator (STV), precision digital multi-
meter (DMM), and ZERO-CON to the input terminals. Connect to the corre-
sponding input terminals when adjusting inputs 0 to 3.

Note

The personal computer (CX-Integrator) is connected through CompoNet in
the above diagram. If a CS1W-CRM21 or CJ1W-CRM21 Master Unit is being
used, the Temperature Input Unit can be adjusted by connecting the CX-Inte-
grator through the Master Unit using a peripheral bus connection.

CompoNet

CRT1-TS04T

DeviceNet Configurator
CX-Integrator

Compensating
conductors

Reference voltage/current generator (STV)
Remove when performing bias compensation.

Precision digital multimeter (DMM)
Use to confirm that the STV is generating an accurate voltage.

Cold junction compensator (such as a ZERO-CON)
Leave open (disabled) until performing bias compensation.

«
...
501
502
503
504
505
...
»

Содержание CRT1 - 10-2008









































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CRT1 - 10-2008

Бренд: Harry Taylor Страницы: 56

Бренд: Harry Taylor Страницы: 52

Бренд: Jetmaster Страницы: 23

Бренд: Cantherm Страницы: 11

Бренд: Oceanic Страницы: 201

Бренд: Paloma Страницы: 28

Бренд: Vornado Страницы: 15

Бренд: JLF Страницы: 5

Elnur INGENIUM RD10W

Бренд: Gabarron Страницы: 12

Бренд: LVI Страницы: 8

Бренд: Mr. Heater Страницы: 16

Бренд: Dimplex Страницы: 20

Бренд: Lavor Страницы: 20

Бренд: G21 Страницы: 36

Бренд: SSHEAT Страницы: 12

Бренд: Loopcomm Страницы: 2

Бренд: Dimplex Страницы: 20

Бренд: Vitesse Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды