Omron CRT1 - 10-2008 Скачать руководство пользователя страница 352 | Manualshive

Страница: 352 / 584

background image

329

Status Areas

Section 7-3

7-3

Status Areas

A Temperature Input Unit has two status areas. The flags are turned ON and
OFF based on the threshold values set by the user for each function in that
Unit.

If any flag in a Status Area in the Slave Units connected to the Master Unit
turns ON, a corresponding status flag in the Master Unit turns ON. Bit 12 in
the Master Unit corresponds to the Warning Status Area and bit 13 corre-
sponds to the Alarm Status Area.

The Temperature Input Unit's status area information can be read by using the
CX-Integrator or explicit messages.

Warning Status Area

The Temperature Input Unit's Warning Status Area contains the following 16
bits. These bits indicate minor errors in the Unit.

Master Unit

The Master Unit has a Warning Status Bit and Alarm
Status Bit.
The status of each of these bits is an OR status of the
bits in the status area in the connected Slave Unit.

Transmitted to Master Unit

Temperature Input Unit

The Status Area in the Temperature Input
Unit has a Warning Status Area and an
Alarm Status Area.

Bit

Content

Description

0

Reserved.

Cannot be used.

1

Reserved.

Cannot be used.

2

Network Power Voltage Drop Flag

OFF: Normal

ON: Error (Voltage dropped below
threshold.)

Turns ON when the Network Power
Voltage drops below the voltage set as
the threshold for monitoring.

3

Unit Maintenance Flag

OFF: Normal

ON: Error (Threshold exceeded.)

Turns ON when the Total Unit Conduc-
tion Time exceeds the value set as the
threshold for monitoring.

4

Reserved.

Cannot be used.

5

Reserved.

Cannot be used.

6

Reserved.

Cannot be used.

7

Reserved.

Cannot be used.

8

Temperature Input Warning Flag

OFF: Within range (below set moni-
tor value)

ON: Out-of-range (equal to or above
set monitor value)

Turns ON when the temperature data
exceeds the displayable range or the
monitor value set for the comparator
function.

9

Cumulative Counter Exceeded Flag

OFF: Within range (below set moni-
tor value)

ON: Out-of-range (equal to or above
set monitor value)

Turns ON when the cumulative value
exceeds the set monitor value.

«
...
350
351
352
353
354
...
»

Содержание CRT1 - 10-2008









































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CRT1 - 10-2008

Бренд: VEAB Страницы: 16

Бренд: Lasko Страницы: 6

Бренд: SoundBrick Страницы: 20

Бренд: Omega Altise Страницы: 8

Бренд: Far Group Страницы: 12

Бренд: Melchioni Страницы: 44

INFRARED HEATER

Бренд: lifeSMART Страницы: 17

Бренд: Vam Teplo Страницы: 16

Бренд: Goldair Страницы: 12

Бренд: Vogel & Noot Страницы: 8

Бренд: Powrmaster Страницы: 14

Бренд: Range Страницы: 4

Бренд: G.M. International Страницы: 11

Бренд: NEO TOOLS Страницы: 47

Бренд: Ouellet Страницы: 2

Бренд: Klarstein Страницы: 76

Бренд: Hyundai Страницы: 24

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды