Omron CP1H-CPU - 05-2006, Руководство по эксплуатации

Страница: 560 / 669

529
Auxiliary Area Allocations by Address
Appendix D
A213 A213.00
to
A213.07 Explicit Com-
munications
Error Flag Turn ON when an error occurs in
executing an Explicit Message
Instruction (EXPLT, EGATR, ESATR,
ECHRD, or ECHWR).
Bits 00 to 07 correspond to commu-
nications ports 0 to 7.
The corresponding bit will turn ON
both when the explicit message can-
not be sent and when an error
response is returned for the explicit
message.
The status will be maintained until
the next explicit message communi-
cation is executed. The bit will always
turn OFF when the next Explicit Mes-
sage Instruction is executed. ON: Error end
OFF: Normal
end
Retained --- --- A219.00
to
A219.07
A203 to
A210
A214 A214.00
to
A214.07 First Cycle
Flags after
Network Com-
munications
Finished Each flag will turn ON for just one
cycle after communications have
been completed. Bits 00 to 07 corre-
spond to ports 0 to 7. Use the Used
Communications Port Number stored
in A218 to determine which flag to
access.
Note These flags are not effective
until the next cycle after the
communications instruction is
executed. Delay accessing
them for at least one cycle.
ON: First
cycle after
communica-
tions finish
only
OFF: Other
status
--- ---
A215 A215.00
to
A215.07 First Cycle
Flags after
Network Com-
munications
Error Each flag will turn ON for just one
cycle after a communications error
occurs. Bits 00 to 07 correspond to
ports 0 to 7. Use the Used Communi-
cations Port Number stored in A218
to determine which flag to access.
Determine the cause of the error
according to the Communications
Port Completion Codes stored in
A203 to A210.
Note These flags are not effective
until the next cycle after the
communications instruction is
executed. Delay accessing
them for at least one cycle.
ON: First
cycle after
communica-
tions error
only
OFF: Other
status --- ---
A216
to
A217 All Network Com-
munications
Completion
Code Storage
Address The completion code for a communi-
cations instruction is automatically
stored at the address with the I/O
memory address given in these
words.
Place this address into an index reg-
ister and use indirect addressing
through the index register to read the
communications completion code. I/O memory
address for
the network
communica-
tions comple-
tion code
storage --- ---
A218 All Used Commu-
nications Port
Numbers Stores the communications port
numbers used when a communica-
tions instruction is executed using
automatic communication port allo-
cations. 0000 to 0007
hex: Commu-
nications port
0 to 7 --- ---
A219 A219.00
to
A219.07 Communica-
tions Port
Error Flags ON when an error occurred during
execution of a network instruction
(SEND, RECV, CMND, or PMCR).
Bits 00 to 07 correspond to commu-
nications ports 0 to 7.
ON: Error
occurred
OFF: Normal
condition
Retained --- --- ---
A262
and
A263 All Maximum
Cycle Time These words contain the maximum
cycle time since the start of PLC
operation. The cycle time is recorded
in 8-digit hexadecimal with the left-
most 4 digits in A263 and the right-
most 4 digits in A262. 0 to
FFFFFFFF:
0 to
429,496,729.
5 ms
(0.1-ms units)
--- --- --- ---
Address Name Function Settings Status
after
mode
change
Status
at star-
tup
Write
timing
Related
flags, set-
tings
Words Bits