10.3 Alarm Message List
10-43
4444
UNSUCCESSFUL
FINE POSITIONING
[Binary Data]
• When executing PL=0 or interrupting
external servo, the servo deflection was
not put within time.
• Excessive external force
• The servopack, the motor were abnormal.
• Reset the alarm. In case an external
force is affecting the robot, move the
robot to remove the external force and
repeat the operation.
• In case the phenomenon occurs again
without any external force, try to insert
the XCP01 circuit board again.
• If the error occurs again, contact you
YASKAWA representative.
4445
DATA PRESET
ERROR
[Decimal Data]
When the interpretation process section of
job annulled the content of interpretation
and started to interpret again, various kinds
of data were attempted to be initialized. At
the time, a disagreement of data occurred.
Data (1-255) stands for the alarm factor.
• Reset the alarm. Select the job and
repeat the operation.
• If the error occurs again, contact you
YASKAWA representative.
4446
OVER VARIABLE
LIMIT
[Decimal Data]
The range of the numerical value of the vari-
able for storage destination was exceeded.
Increase the variable range at the storage
destination or rewrite the job to bring the
number of variables in range.
4447
DEFECTIVE TAUGHT
POINT
(CIRC)
A straight line linked the three points.
Reset the alarm and teach again.
4448
WEAVING CON-
TROL ERROR
[Decimal Data]
When executing the weaving motion control,
the control error occurred in the path opera-
tion process.
Data stands for the alarm factor.
4:Weaving speed instruction was moving
time instruction, moving time was less
than 0.
5:Weaving speed instruction was frequency
instruction, frequency was less than 0.
6.Weaving stopping time was negative
7:Vertical direction distance at or horizontal
direction distance was 0 in triangular
wave, L type weaving.
9:Distance between P point and control
point was less than 0 in the wrist weaving
Except above: Control error
• 4:Set 0.1 seconds or more in the moving
time of weaving file.
• 5:Set 0.1 hertz or more in the frequency
of weaving file.
• 6:Set a positive value in the stopping
time of weaving file.
• 7:Set 1mm or more in the vertical direc-
tion, horizontal direction distance of
weaving file.
• If the error occurs again, contact you
YASKAWA representative.
4449
UNMATCHED POSN
VAR DATA TYPE
[Bit Pattern]
The data types (pulse, Cartesian) of the
stored data and the storage destination are
different.
Match the data types (pulse, Cartesian) of
the stored data and the storage destina
tion.
4450
FILE NO. ERROR
[Decimal Data]
The error occurred during file No. check.
Data stands for the alarm factor.
• Reset the alarm. Select the job and
repeat the operation.
• If the error occurs again, contact you
YASKAWA representative.
4451
UNDEFINED REFER-
ENCE POINT
[Bit Pattern]
No reference point was registered or insuffi-
cient reference points were registered.
Correctly register reference points.
4452
STACK MORE THAN
8 (JOB CALL
[Decimal Data]
The job call stack overflowed.
Reset the alarm and modify the job to
reduce the jobs in the job call stack.
4453
OVER VARIABLE
NO.
[Bit Pattern]
A variable number was out-of-range.
Modify the job by using the permitted vari-
able number.
Alarm Message List
Alarm
Number
Message
Cause
Remedy
Содержание SK300X
