background image

2.8  General I/O Signal Assignment

2-53

*1

A master job is a job (program) which can be called by CALL MASTER JOB. 
Other functions are the same as for normal jobs. Normally, the parent job, which man-
ages the child jobs called up immediately after the power is turned ON, is set as the 
master job. 

*2

See " 3.7  Interference Area " of the YASNAC XRC Instructions.

Specific Output List XCO02B (Handling)

Logical

Number

Output Name / Function

Logical

Number

Output Name / Function

3010

RUNNING
This signal signifies that the job is run-
ning. (Signifies that the job is running, 
system status is waiting reserved start, 
or test run is running.) This signal status 
is the same status as [START] in the 
playback panel.

3021

IN CUBE 2
This signal turns ON when the current 
tool center point lies inside a pre-defined 
space (Cube 2). Use this signal to pre-
vent interference with other manipulators 
and jigs. 

3011

SERVO IS O
This signal signifies that the servo power 
is turned ON, internal processing such 
as current position creation is complete, 
and the system is able to receive the 
START command. This signal turns OFF 
when the servo power supply turns OFF. 
It can be used for XRC status diagnosis 
for an external start. 

3022

OPERATION ORIGIN POINT (IN CUBE 

24)

*1

This signal turns ON when the current 
tool center point lies inside a the opera-
tion origin area. Use this signal to evalu-
ate whether the robot is in the start 
position.

3012

TOP MASTER JOB
This signal signifies that the execution 
position is the top of the master job. This 
signal can be used to confirm that the 

master job has been called.

*2

3023

INTERMEDIATE START OK (Sequence 
continues)
This signal turns ON when the manipula-
tor operates. It turns OFF when the cur-
rently executed line is moved with the 
cursor or when editing operation is car-
ried out after HOLD is applied during 
operation. Therefore, this signal can be 
used as a restart interlock after a HOLD 
is applied. However, it also turns ON in 
the TEACH mode and TEACH MODE 
SELECTED signal must be referred 
together.

3013

ALARM/ERROR OCCURRING
This signal signifies that an alarm or an 
error occurred. If a major error occurs, 
this signal remains ON until the main 
power is turned OFF.

3040 to

3047

HAND VALVE 1-4
These outputs are controlled by the 
HAND handling specific instructions. 
Hand valves 1 to 4 correspond to HAN
1 to 4. 

3014

BATTERY ALARM
This signal turns ON to notify that the 
battery requires replacing when the volt-
age drops from the battery for backup 
memory of the encoder. Major problems 
may result if memory data is lost 
because of an expired battery. It is rec-
ommended to avoid these problems by 
using this signal as a warning signal.

Содержание SK300X










































































































































































































































































































































































































































































































































































Отзывы: