Keithley 6517B Скачать руководство пользователя страница 321 | Manualshive

Страница: 321 / 498

background image

Section 14: SCPI command reference

Model 6517B Electrometer Reference Manual

14-70

6517B-901-01 Rev. C / August 2015

:VSOurce[:AMPLitude] <n>

This command is used to set the V-source level for Manual V-source Ohms

Usage

[:SENSe[1]:RESistance:MANual:VSOurce[:AMPLitude] <n>
[:AMPLitude]?
[:AMPLitude]? DEFault
[:AMPLitude]? MINimum
[:AMPLitude]? MAXimum

<n>



-100 to 100:

Set voltage for 100V range



-1000 to 10000:

Set voltage for 1000V range



DEFault:

0V



MINimum:

Greatest allowable negative value



MAXimum:

Greatest allowable positive value

Details

This command is used to set the V-source level for Manual V-source Ohms. With Auto V-source
Ohms selected, you are not able to adjust the V-source level.

The amplitude level is limited by the selected V-source range. When on the 100V range, attempts to
set the amplitude to a value that exceeds 100V results in a Settings Conflict error. The amplitude may
also be limited by the

:SOURce:VOLTage:LIMit[:AMPLitude]

command. Attempts to set an

amplitude that exceeds this programmed limit sets the amplitude to that limit.

The

MINimum

and

MAXimum

parameters are also affected by range and voltage limit. Setting the V-

source to the

MINimum

(or

MAXimum

) amplitude selects the greatest negative (or positive) value

allowed by the programmed limit or range. The V-source output (operate or standby) is controlled
from the

:OPERate

command.

Also see

:VSOurce:RANGe <n>
:VSOurce:OPERate <b>

:VSOurce:OPERate <b>

This command is used to enable or disable the V-source.

Usage

[:SENSe[1]:RESistance:MANual:VSOurce:OPERate <n>
:OPERate?

<b>

ON or 1:

Enable V-source (operate)

OFF or 0:

Disable V-source (standby)

Details

This command is used to enable or disable the V-source for Manual V-source Ohms. When enabled, the V-source
is placed in operate. When disabled, the V-source is placed in standby.

Also see

None

«
...
319
320
321
322
323
...
»

Содержание 6517B



















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6517B

Бренд: Valeport Страницы: 25

Бренд: YOKOGAWA Страницы: 3

Бренд: Kawai Страницы: 33

Бренд: Kawai Страницы: 60

Бренд: Kane Страницы: 19

Power Xpert PXM 4000

Бренд: Eaton Страницы: 28

Бренд: Hardy Barth Страницы: 27

Бренд: Saimo Страницы: 101

Бренд: M-system Страницы: 16

Бренд: M-system Страницы: 25

Бренд: Nady Audio Страницы: 2

Бренд: RADWAG Страницы: 12

Бренд: Veeder-Root Страницы: 59

Бренд: YOKOGAWA Страницы: 16

Бренд: Stübbe Страницы: 12

SF6 Portable Monitor

Бренд: Bacharach Страницы: 2

Бренд: Seben Страницы: 16

Бренд: Badger Meter Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды