Keithley 6517B Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 498

background image

Section 1: Getting started

Model 6517B Electrometer Reference Manual

1-4

6517B-901-01 Rev. C / August 2015

Case and rack mount kits

Model 1050 Padded Carrying Case:

A carrying case for a Model 6517B. Includes handles and

shoulder strap.

Model 4288-1 Single Fixed Rack Side Mount Kit:

Mounts a Model 6517B in a standard 19 inch

rack.

Model 4288-2 Dual Fixed Rack Side Mount Kit:

Mounts two Model 6517B instruments in a standard

19 inch rack.

Model 4288-5 Dual Fixed Rack Shelf Mount Kit:

Mounts two Model 6517B instruments side-by-side

in a standard 19 inch rack.

Model 4288-7 Rear Support Rack Shelf Mount Kit:

Provides added support where one or two card

modules are installed in a mainframe.

Model 4288-9 Dual Fixed Rack Shelf Mount Kit:

Mounts two Model 6517B instruments side-by-side

in a standard 19 inch rack.

Model 4299-7 Universal Fixed Rack Shelf Mount Kit:

Mounts one or two Model 6517B instruments

side-by-side in a standard 19 inch rack.

Probes

Model 6517-RH Humidity Probe with Cable:

This sensor allows the Model 6517B to make relative

humidity measurements (0 % to 100 %). Also included is an extension cable (part number CA-129-1).

Model 6517-TP Thermocouple with Leads:

This type K thermocouple sensor allows the Model

6517B to make external temperature measurements from –190° C to 1350° C.

Scanner cards

Model 6521 Low Current Scanner Card:

This 10-channel low current scanner card is terminated

with BNC connectors and plugs into the option slot of the Model 6517B.

Model 6522 Low Current/Low Voltage Scanner Card:

This 10-channel low current/low voltage

scanner card is terminated with triaxial connectors and plugs into the option slot of the Model 6517B.

Text fixture

Model 8009 Resistivity test Fixture:

This is a guarded test fixture for measuring volume and surface

resistivities. It can accommodate sheet samples 64 mm to 102 mm (2½ to 4 inches) in diameter and
up to 3.175 mm (1/8 inches) thick.

Software

Model 6524 Hi-R Software Package:

Designed to aid in making more repeatable high

resistance/resistivity measurements. Four windows-driven programs increase measurement
precision, ease download and analysis of Hi-R data, and allow cross-correlation of environmental
factors.

«
...
18
19
20
21
22
...
»

Содержание 6517B



















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6517B

Бренд: HANYOUNGNUX Страницы: 4

Бренд: NCTE Страницы: 10

Бренд: Van Walt Страницы: 12

Бренд: National Instruments Страницы: 85

Бренд: National Instruments Страницы: 12

Бренд: National Instruments Страницы: 18

Бренд: National Instruments Страницы: 12

Бренд: Raymarine Страницы: 42

Бренд: Tavool Страницы: 12

STORA-ABG RKS-01

Бренд: ECOTEST Страницы: 146

Бренд: H. HERMANN EHLERS Страницы: 40

Бренд: Chauvin Arnoux Страницы: 44

Бренд: Droplet Страницы: 35

Бренд: Sencore Страницы: 75

Бренд: truflo Страницы: 33

Бренд: Hach Страницы: 4

Бренд: Hanna Instruments Страницы: 16

Retinomax K+Screeen

Бренд: Righton Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды