manualshive.com logo in svg

Keithley 6517B, Справочное руководство

Прибор Keithley 6517B - идеальное решение для измерения небольших токов и высоких сопротивлений. Посетите manualshive.com, чтобы бесплатно скачать руководство пользователя с ключевыми инструкциями по использованию. Доверьтесь профессиональной документации для вашего прибора.

Поделиться
Скачать
background image

Model 6517B Electrometer Reference Manual 

Section 10: Limits, digital I/O, and scanning 

 

6517B-901-01 Rev. C / August 2015 

10-11 

 

External scanning 

When using external scanning, you can configure the Model 6517B to measure up to 400 channels. 
In order to synchronize Model 6517B measurements with external channel closure, connect the 
Model 6517B trigger link to the external switching mainframe trigger link (see 

Triggering

 (on page 7-

1)). 

Use the following information to configure the Model 6517B for external scanning, and to start the 
external scan. Refer to the documentation supplied with the switching mainframe and the scanner 
card for specific configuration and connection information. 

The following procedure uses menu structures to configure the instrument for external scanning. 

1.  Set up the Model 6517B for the desired measurement (for example, set function, range, etc.).If 

there is no card installed in the option slot of the Model 6517B, external scanning is automatically 
be selected. If there is a card installed in the option slot, you must select external scanning as 
explained in the following step: 

2. Press 

CONFIG

 and then 

CARD

, and perform step a or b. 

a.  Option slot empty: You are prompted to specify the number of external channels (inputs) to 
scan. After entering the value, press 

ENTER

. 

b.  Card installed in option slot: Select the 

EXTERNAL-INPUTS (CHANNELS)

 option from the menu and 

then specify the number of external channels (inputs) to scan. After entering the value, press 

ENTER

. 

Use the 

EXIT

 key to back out of the menu structure. 

3. Press 

the 

CARD

 key and perform step a or b. 

a.  Option slot empty: The displayed message prompts you to reset the external scanner. Press 

ENTER

 when ready. 

b.  Card installed in option slot: Select the 

PERFORM-SCAN

 option from the menu and select 

EXTERNAL

 

scanning. The 

CHANNEL-CLOSURES

 option is used to open/close channels on the scanner card 

installed in the option slot. For details, see the instruction manual for that card. The displayed message 
prompts you to reset the external scanner. Press 

ENTER

 when ready. 

4.  The next message prompts you to set the channel count (CHAN COUNT) of the external scanner 

to infinite. Press 

ENTER

 when ready. 

5.  The next message prompts you to select the trigger source for the Model 6517B: 

 
SELECT TRIG SOURCE 
TRIGLINK EXTERNAL TIMER GPIB 
MANUAL IMMEDIATE 
 
These trigger sources are explained in 

Triggering

 (on page 7-1). 

6.  The next message prompts you to set the external scanner to the trigger source that you selected 

in step 5 for the Model 6517B. Press 

ENTER

 when ready. 

7.  The next message prompts you to set the scan list of the external scanner for the appropriate 

number of channels. This is the same number of external inputs that was specified in step 2. 
Press 

ENTER

 when ready. 

8.  The next message prompt you to 

STEP

 the external scanner to the first channel. Press 

ENTER

 

when ready. 

9.  The next message prompt you to set the scan count for the Model 6517B. The scan count 

specifies how many times you wish to repeat the scan. For example, if the scan list has 40 
channels, and the scan count is 5, then 40 channels are scanned five times. Press 

ENTER

 when 

ready. 

10.  The next message asks if you wish to use the scan timer of the Model 6517B. If you selected 

TIMER as the trigger source in step 5, select 

YES

. You are then be prompted to enter the interval 

between triggers (0.001 second to 999999.999 seconds). Otherwise, select 

NO

. 

Содержание 6517B



















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6517B

Datavideo TL-1 User Manual preview
TL-1
Бренд: Datavideo Страницы: 26
Datcon DT4200 Operating Instructions Manual preview
DT4200
Бренд: Datcon Страницы: 84
LATNEX RF Explorer User Manual preview
RF Explorer
Бренд: LATNEX Страницы: 55
Laser Technology TruPulse 200X Quick Reference Manual preview
TruPulse 200X
Бренд: Laser Technology Страницы: 11
Laser Technology TruPulse 200X User Manual preview
TruPulse 200X
Бренд: Laser Technology Страницы: 62
X-Rite RM200QC User Manual preview
RM200QC
Бренд: X-Rite Страницы: 45
X-Rite i1Pro Quick Start Manual preview
i1Pro
Бренд: X-Rite Страницы: 22
E-Mon Din-Mon D5 Installation Instructions Manual preview
Din-Mon D5
Бренд: E-Mon Страницы: 72
bmcm meM-INC Quick Start Manual preview
meM-INC
Бренд: bmcm Страницы: 5
Tektronix TAS 200 Instruction Manual preview
TAS 200
Бренд: Tektronix Страницы: 48
Circutor Wibeee Max Instruction Manual preview
Wibeee Max
Бренд: Circutor Страницы: 48
Primes Cube L1 Original Instructions Manual preview
Cube L1
Бренд: Primes Страницы: 56
J&D Electronics Multi-GEM 12 User Manual preview
Multi-GEM 12
Бренд: J&D Electronics Страницы: 2
3M SP-SE-2-1/1 User Manual preview
SP-SE-2-1/1
Бренд: 3M Страницы: 168
Chauvin Arnoux PHYSICS line C.A 832 User Manual preview
PHYSICS line C.A 832
Бренд: Chauvin Arnoux Страницы: 43
Lambda SRS SR475 Operation Manual preview
SRS SR475
Бренд: Lambda Страницы: 35
Major tech MT 770 Instruction Manual preview
MT 770
Бренд: Major tech Страницы: 16
Ocean Optics CHEM2000-UV-VIS Operating Manual And User Manual preview
CHEM2000-UV-VIS
Бренд: Ocean Optics Страницы: 42

Бренды по названию

Популярные бренды

Загрузить еще бренды