Keithley 6517B Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 498

background image

Section 1: Getting started

Model 6517B Electrometer Reference Manual

1-6

6517B-901-01 Rev. C / August 2015

General ratings

The Model 6517B instrument's general ratings and connections are listed in the following table.

Category Specification

Supply voltage range

100 to 240 VAC, 50 Hz or 60 Hz (autosensing at power on)

Input and output connections

See Rear panel overview.

Environmental conditions

For indoor use only

Altitude:

Maximum 2000 meters (6562 feet) above sea level

Operating:

0 °C to 50 °C (32 °F to 122 °F),

≤

70 % relative humidity, non-

condensing, up to 35 °C (95 °F)

Storage:

-25 °C to 65 °C (



13 °F to 149 °F)

Pollution degree:

1 or 2

Unpacking and inspection

Inspection for damage

The Model 6517B was carefully inspected electrically and mechanically before shipment. After
unpacking all items from the shipping carton, check for any obvious signs of physical damage that
may have occurred during transit. There may be a protective film over the display lens, which can be
removed. Report any damage to the shipping agent immediately. Save the original packing carton for
possible future shipment. Before removing the Model 6517B from the anti-static bag, observe the
following handling precautions.

Handling precautions



Always grasp the Model 6517B by the covers.



After removing the Model 6517B from its anti-static bag, inspect it for any obvious signs of
physical damage. Report any such damage to the shipping agent immediately.



When the Model 6517B is not installed and connected, keep the unit in its anti-static bag and
store it in the original packing carton.

Shipment contents

The following items are included with every Model 6517B order:



Model 6517B Electrometer with line cord



Protective Triaxial Shield/Cap (CAP-28-1)



237-ALG-2 Triaxial Cable terminated with alligator clips on one end



Accessories as ordered



Certificate of calibration

Always check the Keithley Instruments website at

www.keithley.com

(

http://www.keithley.com

) for the

latest revisions of the instruction manuals, which can be downloaded in PDF format from the website.

«
...
20
21
22
23
24
...
»

Содержание 6517B



















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6517B

Бренд: ABB Страницы: 8

Бренд: M3S Страницы: 40

CP-4900 Micro-GC

Бренд: Varian Страницы: 7

Бренд: Vapotherm Страницы: 2

Бренд: Xylem Страницы: 19

Бренд: horiba Страницы: 27

Бренд: THORLABS Страницы: 21

Бренд: Lutron Electronics Страницы: 43

Бренд: Omega Страницы: 20

Бренд: TAC Страницы: 28

Бренд: ProDetec Страницы: 49

Orion Lab Star PH111

Бренд: ThermoFisher Scientific Страницы: 40

Part Per Million PPM-1c

Бренд: CAP Страницы: 2

Бренд: Iradion Страницы: 34

Sphensor PRMPA0401

Бренд: LSI LASTEM Страницы: 32

Бренд: IBA Страницы: 48

Бренд: Spectra Precision Страницы: 111

Бренд: National Instruments Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды