Keithley 6517B Скачать руководство пользователя страница 231 | Manualshive

Страница: 231 / 498

background image

Model 6517B Electrometer Reference Manual

Section 12: Common commands

6517B-901-01 Rev. C / August 2015

12-9

*OPC? (operation complete query)

This command places a 1 in the output queue after all pending operations are completed.

Details

On power-up, or when

*CLS

or

*RST

is executed, the Model 6517B goes into the operation complete

command query idle state (OQIS). In this state there are no pending overlapped commands. The
overlapped commands used by the Model 6517B are:



:INITiate:CONTinuous ON



:INITiate



*TRG

When the

*OPC?

command is sent, the Model 6517B exits from OQIS and enters the operation

complete command active state (OQAS). In OQAS, the instrument continuously monitors the no-
operation-pending flag. After the last pending overlapped command is completed (no-operation-
pending flag set to true), an ASCII character 1 is placed into the output queue, the message available
(MAV) bit in the status byte sets, and the instrument goes back into OQIS. Addressing the Model
6517B to talk sends the ASCII 1 to the computer.

Note that the instrument always goes into OQAS when

*OPC?

is executed. If there are no pending

command operations (for example, trigger model in idle state), the Model 6517B immediately places
an ASCII "1" in the output queue, sets the MAV bit and returns to OQIS.

When used with the

:INITiate

or

:INITiate:CONTinuous ON

command, an ASCII "1" is not

sent to the output queue and the MAV bit is not set until the Model 6517B goes back into the idle
state. The initiate operations are not considered finished until the instrument goes into the idle state.

The

:INITiate:POFLag

command is used to include or exclude the no-operation-pending flag in

the internal process of determining whether all pending operations of an initiate command are
completed.

When used with the

*TRG

command, an ASCII 1 is not placed into the output queue and the MAV bit

is not set until the operations associated with the

*TRG

command (and the initiate command) are

finished. The

*TRG

command is considered to be finished when the device action completes or when

operation stops at a control source to wait for an event (see

IEEE-488 trigger model

(on page 11-16)

for more information).

In order to use

*OPC?

exclusively with the

*TRG

command, you must force the completion of the

initiate command so that only the

*TRG

command is pending. To do this, send the

:ABORt

command

to place the instrument in idle, which (by definition) completes the initiate command. Since continuous
initiation is on, operation continues on into the trigger model. After sending the

*TRG

command, an

ASCII 1 is placed in the output queue and the MAV bit sets when the

*TRG

command is finished.

After

*OPC?

is executed, additional commands cannot be sent to the Model 6517B until the pending

overlapped commands have finished. For example,

:INITiate:CONTinuous ON

followed by

*OPC?

locks up the instrument and requires a device clear (DCL or SDC) before it accepts any more

commands. See

*OPC, *TRG,

and

*WAI

for more information.

Also see

*OPC

(on page 12-8)

*TRG (trigger)

(on page 12-14)

*WAI (wait-to-continue)

(on page 12-15)

«
...
229
230
231
232
233
...
»

Содержание 6517B



















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6517B

Бренд: Samson Страницы: 4

HF Scientific AccUView LED Ex

Бренд: Watts Страницы: 2

Бренд: S.E. International Страницы: 30

Бренд: SZBJ Страницы: 2

Бренд: S+S Regeltechnik Страницы: 32

Бренд: PASCO Страницы: 4

DELMHORST J-2000

Бренд: ABQ Industrial Страницы: 4

Бренд: General Страницы: 12

miniSERIES Series

Бренд: Valeport Страницы: 25

Seeker 400 Series

Бренд: General Страницы: 24

Бренд: shelyak Страницы: 45

Бренд: J&D Electronics Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Omega Страницы: 2

E INSTRUMENTS 1500

Бренд: sauermann Страницы: 170

Бренд: Lapp Automaatio Страницы: 2

Бренд: Vega Страницы: 40

InnovaSonic 205i

Бренд: Sierra Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды