Huawei FusionCol8000-E240 Скачать руководство пользователя страница 24

Страница: 24 / 305

No.

Item

Description

Air

supply

fan

● A Huawei-developed high-speed fan is used, which

features large air volume, high static pressure, high

reliability, and a long service life.

● The fan is separated from the drive. The fan efficiency is

improved by more than 8% compared with a common EC

fan.

● The direct drive that the fan adopts has higher

transmission efficiency than the belt drive, which reduces

belt replacement and routine checks.

Compres

sor

● The FusionCol8000-E uses a DC variable-frequency

compressor that features compact size, light weight, a

long service life, low noise, easy installation, high

reliability, stability, and energy efficiency.

● The high-precision drive automatically adapts to the

system pressure fluctuations.

● The drive conducts precision self-check. Compressor and

drive faults are separated.

Compres

sor drive

● The variable-frequency compressor drive, water pump

drive, and 24 V power module are integrated into one

device to save space in the smart cooling product and

improve efficiency.

● The compressor drive is controlled over RS485. You can

view the drive running status and parameters on the

display module in real time to facilitate fault locating.

Liquid

level

sensor

● Liquid level sensor (at the bottom of the precooling

module): A high liquid level sensor is added under the

precooling module. If the precooling module is abnormal,

an alarm is generated in advance.

● Liquid level sensor (inside the spray water tank): There are

three liquid level sensors in the spray water tank, which

are associated with the water refill and drainage systems.

If the water level in the water tank is lower than the low

liquid level sensor, water refill starts. If the water level in

the water tank is higher than the high liquid level sensor,

water refill stops. If the water level in the water tank is

higher than the overflow water level sensor, an alarm is

generated and water is drained.

Fan drive ● Compared with fan speed control by the belt drive, fan

speed control by the direct drive has a wider application

range which is not subject to the transmission ratio.

● The fan is controlled over RS485. You can view the fan

power and speed in real time on the display module and

can obtain fault information including fan blockage,

overvoltage, and undervoltage. The features allow you to

view the status and locate a fault.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

2 Product Description

Issue 02 (2021-04-15)

Содержание FusionCol8000-E240


















































































































































































































































































































Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E240, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды