Huawei FusionCol8000-E240 Скачать руководство пользователя страница 118

Страница: 118 / 305

Procedure

Step 1 On the home screen, choose Settings > System Settings > Indoor fan, set Air-

side difference pressure sensor type to 0-500 Pa.

Step 2 Set Indoor fan control type to Pressure diff ctrl.
Step 3 Change the other parameters based on the following instructions.

Table 6-4 Description

Parameter

Description

Configuration Principle

Indoor fan control

type

Sets the control type for

the indoor fan.

Normally, retain R/S air

temp diff rate ctrl. If the

differential pressure sensors

are configured, change to

Pressure diff ctrl.

Indoor fan silent

mode

Set maximum speed of

indoor fan to reduce

equipment noise.

You are advised not to

change the value.

Indoor fan pressure

difference setpoint

Sets the value for the

pressure difference

control.

You are advised not to

change the value.

Air-side difference

pressure sensor type

Sets the measuring range

for the air side

differential pressure

sensor.

There is no default value. Set

it to 0-500 Pa.

Min indoor fan

speed

Sets the minimum speed

for the indoor fan.

The default value is 30%.

You are advised not to

change the value.

Max indoor fan

speed

Sets the maximum speed

for the indoor fan.

The default value is 100%.

----End

6.4.3 (Optional) Setting Teamwork Control Parameters

Prerequisites

The teamwork control numbers and addresses for teamwork controlled smart

cooling products have been set as follows:
●

Teamwork group No.: Group the smart cooling products in same aisle or

adjacent areas as one, that is, assign one teamwork group number for them.

At most four teamwork groups can be assigned (1–4).

●

System address: The address (configurable range: 1-32) of each smart cooling

product in the same group must be unique. The smart cooling product with

the smallest unit address is the master unit, which collects, processes, and

delivers group data.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

6 Power-On Commissioning

Issue 02 (2021-04-15)

109

Содержание FusionCol8000-E240


















































































































































































































































































































Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E240, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды