Huawei FusionCol8000-E240 Скачать руководство пользователя страница 153

Страница: 153 / 305

Symptom

Possible Cause

Solution

The compressor

discharge

temperature is

too high.

The refrigerant loop or

component is blocked.

Clean up foreign matter in

the refrigerant loop.

Air enters the refrigerant

loop.

Exhaust air and repair the

pipeline.

Heat dissipation is poor

because the condenser is

dirty or blocked.

Clean the condenser fins.

The exhaust fan is faulty.

Check whether the exhaust

fan works properly.

The refrigerant is insufficient. Charge more refrigerant.

The compressor

discharge

pressure is too

low.

The refrigerant is insufficient. Charge more refrigerant.

Refrigerant leaks.

Check the pipeline for

leakage.

The exhaust fan drive fails to

be controlled.

Replace the fan drive.

The compressor

suction pressure

is too low or

liquid returns.

The refrigerant is insufficient. Charge more refrigerant.

The indoor temperature is set

too low.

Modify the temperature

setting.

The air filter is dirty or

blocked.

Replace the air filter.

The external residual

pressure is too high, and

airflow decreases.

Check whether the air

channels are blocked.

The condensing pressure is

too low.

Check the condenser.

The compressor

generates a

loud noise.

Liquid is returning to the

compressor.

Check whether the oil

temperature and discharge

temperature are within

normal ranges.

Refrigerant oil is insufficient.

Add refrigerant oil.

The sheet metal fasteners for

securing the compressor

during transportation are not

removed.

Remove the sheet metal

fasteners.

The fan fails to

start.

The switch of the fan is

turned off.

Check the switch of the fan.

The fan is damaged.

Replace the fan.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

8 System Maintenance

Issue 02 (2021-04-15)

144

Содержание FusionCol8000-E240


















































































































































































































































































































Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E240, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды