Huawei FusionCol8000-E240 Скачать руководство пользователя страница 51

Страница: 51 / 305

Table 3-7 Post-installation checklist

No.

Item

Check Method

Expected Result

Contact between

devices and concrete

platforms

Observe.

The device is in close

contact with and

evenly supported by

the concrete

platforms.

Bolts and nuts

Partially tighten them

using a wrench.

Bolts and nuts are

tightened.

Maintenance door

Open and close the

maintenance doors.

All maintenance doors

can be smoothly

opened and closed.

3.3.3 Checking the Refrigerant

Procedure

Step 1 Remove the adjustable side panels for the compressor.
Step 2 Check whether any of the needle valve bonnets shown in

Figure 3-9

is missing.

1. If any bonnet is missing, contact Huawei technical support.
2. If no bonnet is missing, remove the valve bonnets, and press the valve plugs

using the valve bonnets in turn. If gas flows out, the system is normal. If no

gas flows out, contact Huawei technical support.

Figure 3-9 Needle valve positions

(1) Low-pressure needle valve

(2) Liquid pipe needle valve

----End

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

3 System Installation (Building Scenario)

Issue 02 (2021-04-15)

Содержание FusionCol8000-E240


















































































































































































































































































































Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E240, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды