Huawei FusionCol8000-E240 Скачать руководство пользователя страница 226

Страница: 226 / 305

Figure 8-33 Precharging refrigerant

(1) Refrigerant cylinder

(2) Electronic balance

(3) Pressure gauge

(4) Connection nut

(5) Low pressure needle valve (6) Liquid pipe needle valve

Step 2 Slightly open the refrigerant cylinder valve and slightly loosen the connection nut

of the pressure gauge and rubber hose. Tighten the nut when cold air escapes out

of the nut.

Step 3 Put the refrigerant cylinder upside down on the electronic balance. Clear the

reading on the balance.

NO TICE

If the R410A refrigerant is provided by Huawei, put the refrigerant cylinder upside

down when charging the refrigerant. If the refrigerant is not provided by Huawei,

check with the refrigerant provider whether the cylinder has a siphon. If the

cylinder has a siphon, stand the cylinder when charging refrigerant. If the cylinder

has no siphon, put the cylinder upside down when charging refrigerant. These

measures ensure that the refrigerant is charged in the liquid state.

Step 4 Open the low pressure gauge valve. Charge 1 kg of refrigerant from the low

pressure side, and then close the low pressure gauge valve. Then open the high

pressure gauge valve and charge the remaining refrigerant from the liquid pipe

needle valve.

NO TICE

Do not move the hose or refrigerant cylinder when charging refrigerant.

Otherwise, the reading on the electronic balance will be affected.

Step 5 The amount of pre-charged refrigerant must be greater than or equal to half of

the total charge amount calculated and less than or equal to the total charge

amount. If the total refrigerant amount cannot be fully pre-charged, charge the

remaining amount of refrigerant during power-on commissioning.

Step 6 After the refrigerant is charged, close all pressure gauge valves and the refrigerant

cylinder valve.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

8 System Maintenance

Issue 02 (2021-04-15)

217

Содержание FusionCol8000-E240


















































































































































































































































































































Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E240, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды