Huawei FusionCol8000-E240 Скачать руководство пользователя страница 147

Страница: 147 / 305

Comp

onent

Item (on the Basis of Monthly

Maintenance)

Troubleshooting

Water

tank

Check that there is no foreign

matter or silt in the water tank.

Shut down the unit, choose the

diagnostic mode, and open the

drainage valve to empty the

water tank. Do not stir the water

in the tank during the operation.

After emptying the water tank,

use a mop and a broom to clean

the silt out of the water tank.

NOTE

Do not wash a large amount of silt

directly into the drainpipe.

Air

filter

Check that the air filter is clean

and not blocked.
Maintain the air filter once a

quarter on average based on the

geographical and seasonal

conditions.

Remove the old filter, clean the

air filter hole, and install a new

filter.

8.2.3 Yearly Maintenance

Table 8-3 Yearly maintenance checklist

Compone

Item (on the Basis of

Quarterly Maintenance)

Troubleshooting

Sensor

Use a precision T/H sensor to

calibrate the T/H sensors

inside and outside the device.

If the temperature deviation is

greater than 1°C or humidity

deviation is greater than 5%, the

T/H sensor must be calibrated or

replaced.

Welding

point and

needle

valve

Check that welding points and

needle valves do not leak

using soapy water or check

that they are free from oil

stains.

If leaking points are found, retrieve

the refrigerant and weld the

leaking points again. Contact

Huawei technical support for

repair.

Exhaust

fan and

indoor

fan

Enter the diagnosis mode,

start the exhaust fan and

indoor fan, and check whether

the fan runs properly without

any abnormal noise.

Replace the fan.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

8 System Maintenance

Issue 02 (2021-04-15)

138

Содержание FusionCol8000-E240


















































































































































































































































































































Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E240, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды