Huawei FusionCol8000-E240 Скачать руководство пользователя страница 100

Страница: 100 / 305

Figure 4-29 Assembling an air deflector

Step 2 Install the assembled air deflector on the corridor module.

----End

4.6 (Optional) Installing T/H Sensors Outside a Cabinet

and Cables

Context

NO TICE

The T/H sensors outside the cabinet are used to detect the temperature and

humidity of remote points. The installation position can be determined based on

the site requirements. It is recommended that the T/H sensors be deployed near

heat sources, or near places that lack cooling capacity. Place the T/H sensors near

the cabinet. The sensors cannot face the air outlet of the device.

Procedure

Step 1 Connect the IN port on the first T/H sensor outside the cabinet to the RS485/12V

port on the main control module.

Step 2 Connect the OUT port on the T/H sensor outside the cabinet to the IN port on the

next T/H sensor outside the cabinet in series.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

4 System Installation (FDC Scenario)

Issue 02 (2021-04-15)

Содержание FusionCol8000-E240


















































































































































































































































































































Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E240, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды