Huawei FusionCol8000-E240 Скачать руководство пользователя страница 68

Страница: 68 / 305

3.6 (Optional) Installing T/H Sensors Outside a Cabinet

and Cables

Context

NO TICE

The T/H sensors outside the cabinet are used to detect the temperature and

humidity of remote points. The installation position can be determined based on

the site requirements. It is recommended that the T/H sensors be deployed near

heat sources, or near places that lack cooling capacity. Place the T/H sensors near

the cabinet. The sensors cannot face the air outlet of the device.

Procedure

Step 1 Connect the IN port on the first T/H sensor outside the cabinet to the RS485/12V

port on the main control module.

Step 2 Connect the OUT port on the T/H sensor outside the cabinet to the IN port on the

next T/H sensor outside the cabinet in series.

NO TE

● Each smart cooling product supports a maximum of twelve T/H sensors outside the

cabinet, including a maximum of six cold aisle T/H sensors and six hot aisle T/H sensors.

● It is recommended that the total length of the cable required for the T/H sensors

outside the cabinet be less than or equal to 150 m. If the cable length is greater than

120 m, obtain 12 V DC power from the site to supply power to the T/H sensors that are

120 m or further away from the cabinet. Ensure that the input voltage of each T/H

sensor ranges from 9 V to 16 V.

● The T/H sensors outside the cabinet must be connected to a Category 5E cable or a

network cable with higher specifications. Otherwise, the power supply voltage of the

T/H sensors may be insufficient due to large impedance of the network cable. When the

voltage is less than 9 V, the T/H sensors cannot work properly.

Step 3 Set DIP switches of the T/H sensors.

Table 3-9 DIP switch settings on T/H sensors

Locatio

Display Name

Addre

DIP Switch No.

Air

return

side

Return air 2 temp/

humid

OFF

Outdoor

intake

air

Outdoor intake air

1 temp/humid

OFF

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

3 System Installation (Building Scenario)

Issue 02 (2021-04-15)

Содержание FusionCol8000-E240


















































































































































































































































































































Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E240, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды