Huawei FusionCol8000-E240 Скачать руководство пользователя страница 95

Страница: 95 / 305

Networking

Teamwork

Monitoring

Description

One teamwork network

supports a maximum of 32

smart cooling products. On

the Teamwork Settings

screen of the display modules

of the first and last smart

cooling products, set Enable

teamwork CAN resistor to

Yes.

It takes 3 x

seconds to

collect data from

smart

cooling products. If the time

required for the host to collect

data from all smart cooling

products does not meet the

performance requirements,

group the smart cooling

products.
● If devices are not grouped

(

= 1), set RS485

monitoring grouping to

Enable on the Modbus

Settings screen for each

device.

● If devices are grouped (

1; recommended:

≤ 4),

set RS485 monitoring

grouping to Enable on the

Modbus Settings screen

for the device with the

COM/FE port connected.

NO TE

● Connect the COM/FE port on the main control module of the last smart cooling product

in each group to the RS485 port on the host.

● Customers can purchase Huawei's ECC and NetEco for the monitoring system.

Figure 4-23 Connecting communications cables

----End

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

4 System Installation (FDC Scenario)

Issue 02 (2021-04-15)

Содержание FusionCol8000-E240


















































































































































































































































































































Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E240, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды