Huawei FusionCol8000-E240 Скачать руководство пользователя страница 57

Страница: 57 / 305

Step 3 Open the outdoor intake air filter and take out the desiccant bag from the

outdoor air intake compartment.

Step 4 Open the maintenance door and water barrier of the spray pump, and take out

the two desiccant bags from the spray pump compartment.

Step 5 Loosen the three transport fixing bolts of the compressor using a 13# solid wrench

and remove the sheet metal fasteners.

Figure 3-18 Removing sheet metal fasteners from the compressor

NO TE

● Do not remove the bolts.
● Keep the removed sheet metal fasteners properly for future transportation.

Step 6 Tighten the bolts on the compressor again to a torque of 12 N·m.
Step 7 Install the adjustable side panels for the compressor.

----End

3.4 Installing Cables

3.4.1 Precautions

●

Connections of all power cables, control cables, and ground cables must

comply with local electrical regulations, and the cable specifications should

comply with local cabling specifications.

●

For details about the maximum current, see the device nameplate.

●

Check that the input voltage and frequency of the primary power supply meet

the requirements.

●

Only trained and qualified personnel are allowed to connect cables.

●

Before connecting cables, use a multimeter to measure the input voltage and

ensure that the power supply is disconnected.

●

All smart cooling products must be securely grounded before being powered

on.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

3 System Installation (Building Scenario)

Issue 02 (2021-04-15)

Содержание FusionCol8000-E240


















































































































































































































































































































Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды

Huawei FusionCol8000-E240, Руководство пользователя

Результаты поиска

Содержание FusionCol8000-E240

Отзывы:

Похожие инструкции для FusionCol8000-E240

Бренды по названию

Популярные бренды