manualshive.com logo in svg

HP ProCurve 2610-24, Руководство по управлению и настройке

HP ProCurve 2610-24 - сетевой коммутатор с широким функционалом и возможностями для настройки и управления сетью. Управляйте устройством с помощью Management And Configuration Manual, которое можно бесплатно скачать на manualshive.com. Идеальный выбор для оптимизации работы вашей сети.

Поделиться
Скачать
background image

SNMP Version 3 Commands  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-6 

SNMPv3 Enable  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-7 

SNMP Version 3 Users   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-8 

Group Access Levels  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-11 

SNMP Communities  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-12 

Menu: Viewing and Configuring non-SNMP 
version 3 Communities  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-14 
CLI: Viewing and Configuring SNMP Community Names   . . . .  13-16 

SNMP Notification and Traps  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-18 

Trap Features  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-20 

Configuring Trap Receivers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-21 

Enabling and Configuring SNMP Inform  . . . . . . . . . . . . . . . . . .  13-22 
Sending Event Log Messages as Traps   . . . . . . . . . . . . . . . . . . . .  13-24 
Using the CLI To Enable Authentication Traps  . . . . . . . . . . . . .  13-24 

Advanced Management: RMON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-25 

CLI-Configured sFlow with Multiple Instances . . . . . . . . . . . . . . . . .  13-25 

Terminology  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-25 
Configuring sFlow  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-26 
Viewing sFlow Configuration and Status  . . . . . . . . . . . . . . . . . .  13-27 

LLDP (Link-Layer Discovery Protocol)  . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-29 

Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-29 

LLDP Terminology   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-30 

General LLDP Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-31 

Packet Boundaries in a Network Topology   . . . . . . . . . . . . . . . .  13-31 

LLDP Configuration Options  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-31 

Options for Reading LLDP Information Collected by the Switch  . .  13-34 

LLDP Standards Compatibility   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-34 

LLDP Operating Rules   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-35 

LLDP Operation and Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-36 

Viewing the Current LLDP Configuration  . . . . . . . . . . . . . . . . . .  13-36 
Configuring Global LLDP Packet Controls  . . . . . . . . . . . . . . . . .  13-38 
Configuring SNMP Notification Support . . . . . . . . . . . . . . . . . . .  13-41 
Configuring Per-Port LLDP Transmit and Receive Modes  . . . .  13-43 
Configuring LLDP Per-Port Advertisement Content  . . . . . . . . .  13-43 

Displaying Advertisement Data  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-45 

Displaying Switch Information Available for Outbound 
Advertisements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-46 
Displaying LLDP Statistics  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-50 

LLDP Operating Notes   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13-53 

xi 

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

D-Link xStack User Manual preview
xStack
Бренд: D-Link Страницы: 357
B&K HD6 User Manual preview
HD6
Бренд: B&K Страницы: 28
B&K HD6 Getting Started Manual preview
HD6
Бренд: B&K Страницы: 2
Daxten SCOUTCOMBO - Installation Manual preview
SCOUTCOMBO -
Бренд: Daxten Страницы: 7
GarrettCom MAGNUM 6KM Installation And User Manual preview
MAGNUM 6KM
Бренд: GarrettCom Страницы: 24
Harman Kardon ABH 4000 Owner'S Manual preview
ABH 4000
Бренд: Harman Kardon Страницы: 2
IBM 8271 Nways Ethernet LAN Switch User Manual preview
8271 Nways Ethernet LAN Switch
Бренд: IBM Страницы: 210
IDEC HS5L Series Instruction Sheet preview
HS5L Series
Бренд: IDEC Страницы: 8
IDEM SAFETY SWITCHES MPR Operating Instructions preview
MPR
Бренд: IDEM SAFETY SWITCHES Страницы: 2
Lindy 32351 Manual preview
32351
Бренд: Lindy Страницы: 70
Labgear 28574LAB User Manual preview
28574LAB
Бренд: Labgear Страницы: 4
ATEN ALTUSCN KH1508I User Manual preview
ALTUSCN KH1508I
Бренд: ATEN Страницы: 173
Soyntec Nexoos 370 Series User Manual preview
Nexoos 370 Series
Бренд: Soyntec Страницы: 7
Phoenix Contact FL SWITCH SFN 16TX Installation Notes For Electricians preview
FL SWITCH SFN 16TX
Бренд: Phoenix Contact Страницы: 6
Lionel O-72 Owner'S Manual preview
O-72
Бренд: Lionel Страницы: 8
Green Brook KingShield T206-C Installation And Operating Instruction preview
KingShield T206-C
Бренд: Green Brook Страницы: 2
WAGO 852-1111 Mounting, Installation And Handling preview
852-1111
Бренд: WAGO Страницы: 36
MicroNet SP1659P User Manual preview
SP1659P
Бренд: MicroNet Страницы: 123

Бренды по названию

Популярные бренды

Загрузить еще бренды