HP ProCurve 2610-24 Скачать руководство пользователя страница 313 | Manualshive

Страница: 313 / 464

background image

Configuring for Network Management Applications

LLDP (Link-Layer Discovery Protocol)

Data Type

Configuration

Options

Default

Description

Remote Management
Address

Type

4, 6

N/A

Always Enabled Shows the network address type.

Address

4

Default or

Uses a default address selection method unless an optional address is

Configured

configured. See “Remote Management Address”, below.

System Name

6

Enable/Disable

Enabled

Uses the switch’s assigned name.

System Description

6

Enable/Disable

Enabled

Includes switch model name and running software version,
and ROM version.

Port Description

6

Enable/Disable

Enabled

Uses the physical port identifier.

System capabilities

Enable/Disable

Enabled

Identifies the switch’s primary capabilities (bridge, router).

supported

5, 6

System capabilities

Enable/Disable

Enabled

Identifies the primary switch functions that are enabled,

enabled

5, 6

such as routing.

1

The Packet Time-to-Live value is not viewable, but is included in LLDP data packets. (Refer to “Changing the Time-to-

Live for Transmitted Advertisements” on page 13-39.)

2

Subelement of the Chassis ID TLV.

3

Subelement of the Port ID TLV.

4

Subelement of the Remote-Management-Address TLV.

5

Subelement of the System Capability TLV.

6

Populated with data captured internally by the switch. For more on these data types, refer to the IEEE 802.1AB-2005

Standard.

Remote Management Address.

The switch always includes an IP address

in its LLDP advertisements. This can be either an address selected by a default
process, or an address configured for inclusion in advertisements. Refer to “IP
Address Advertisements” on page 13-35.

Debug Logging.

You can enable LLDP debug logging to a configured debug

destination (Syslog server and/or a terminal device) by executing the

debug

lldp

command. (For more on Debug and Syslog, see “Debug and Syslog

Operation” on page C-25.) Note that the switch’s Event Log does not record
usual LLDP update messages.

13-33

«
...
311
312
313
314
315
...
»

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

Бренд: N-Tron Страницы: 2

Бренд: National Instruments Страницы: 32

Бренд: OEM Страницы: 1

QuantaMesh T4000 Series

Бренд: QCT Страницы: 41

Бренд: Canoga Perkins Страницы: 7

Бренд: GarrettCom Страницы: 77

Бренд: Advantech Страницы: 101

GlobeCaster STUDIO 4000

Бренд: Global Streams Страницы: 144

TNM4000-TP36FF4X16G24P

Бренд: MRD Страницы: 38

Бренд: Hama Страницы: 36

DOMINION KX II DKX2-0E-E

Бренд: Raritan Страницы: 257

Бренд: TP-Link Страницы: 34

Бренд: FIBERROAD Страницы: 30

Бренд: Exsys Страницы: 14

DCRS-5200 Series

Бренд: Digital China Networks Страницы: 4

Бренд: 3onedata Страницы: 4

tekmarNet 4 User Switch 481

Бренд: Tekmar Страницы: 12

Бренд: ATEN Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды