HP ProCurve 2610-24 Скачать руководство пользователя страница 295

Страница: 295 / 464

Configuring for Network Management Applications

Using SNMP Tools To Manage the Switch

If you are adding a
community, the
fields in this screen
are blank.

If you are editing an
existing community,
the values for the
currently selected
Community appear
in the fields.

Type the value for this field.

Use the Space bar to select
values for other fields

Figure 13-6. The SNMP Add or Edit Screen

Need Help?

If you need information on the options in each field, press

[Enter]

to move the cursor to the Actions line, then select the

Help

option

on the Actions line. When you are finished with Help, press

[E]

(for

Edit

)

to return the cursor to the parameter fields.

3. Enter the name you want in the Community Name field, and use the Space

bar to select the appropriate value in each of the other fields. (Use the

[Tab]

key to move from one field to the next.)

4. Press

[Enter]

, then

[S]

(for

Save

13-15

Содержание ProCurve 2610-24
















































































































































































































































































































































































































































































Результаты поиска

Содержание ProCurve 2610-24

Отзывы:

Похожие инструкции для ProCurve 2610-24

Бренды по названию

Популярные бренды

HP ProCurve 2610-24, Руководство по управлению и настройке

Результаты поиска

Содержание ProCurve 2610-24

Отзывы:

Похожие инструкции для ProCurve 2610-24

Бренды по названию

Популярные бренды