HP ProCurve 2610-24 Скачать руководство пользователя страница 145

Страница: 145 / 464

Interface Access and System Information

System Information

Configure a System Name, Contact, and Location for the Switch.

help distinguish one switch from another, configure a plain-language identity
for the switch.

Syntax

hostname

<name-string>

snmp-server [contact

<system contact>

] [location

<system location>

]

Both fields allow up to 255 characters.

For example, to name the switch “Blue” with “Ext-4474” as the system contact,
and “North-Data-Room” as the location:

New hostname,
contact, and location
data from previous
commands.

Additional System
Information

Figure 7-8. System Information Listing After Executing the Preceding Commands

7-13

Содержание ProCurve 2610-24
















































































































































































































































































































































































































































































Результаты поиска

Содержание ProCurve 2610-24

Отзывы:

Похожие инструкции для ProCurve 2610-24

Бренды по названию

Популярные бренды

HP ProCurve 2610-24, Руководство по управлению и настройке

Результаты поиска

Содержание ProCurve 2610-24

Отзывы:

Похожие инструкции для ProCurve 2610-24

Бренды по названию

Популярные бренды