HP ProCurve 2610-24 Скачать руководство пользователя страница 440

Страница: 440 / 464

MAC Address Management

Overview

The switch assigns MAC addresses in these areas:

■

For management functions:

• One Base MAC address assigned to the default VLAN (VID = 1)

• Additional MAC address(es) corresponding to additional VLANs you

configure in the switch

■

For internal switch operations: One MAC address per port (See “CLI:
Viewing the Port and VLAN MAC Addresses” on page D-4.)

MAC addresses are assigned at the factory. The switch automatically
implements these addresses for VLANs and ports as they are added to the
switch.

N o t e

The switch’s base MAC address is also printed on a label affixed to the back
of the switch.

Determining MAC Addresses in the
Switch

MAC Address Viewing Methods

Feature

Default

Menu

CLI

Web

view switch’s base (default vlan) MAC address
and the addressing for any added VLANs

n/a

D-3

D-4

—

view port MAC addresses (hexadecimal format)

n/a

—

D-4

—

■

Use the menu interface

to view the switch’s base MAC address and the

MAC address assigned to any non-default VLAN you have configured on
the switch.

N o t e

The switch’s base MAC address is used for the default VLAN (VID = 1) that is
always available on the switch.

D-2

Содержание ProCurve 2610-24
















































































































































































































































































































































































































































































Результаты поиска

Содержание ProCurve 2610-24

Отзывы:

Похожие инструкции для ProCurve 2610-24

Бренды по названию

Популярные бренды

HP ProCurve 2610-24, Руководство по управлению и настройке

Результаты поиска

Содержание ProCurve 2610-24

Отзывы:

Похожие инструкции для ProCurve 2610-24

Бренды по названию

Популярные бренды