HP ProCurve 2610-24 Скачать руководство пользователя страница 147

Страница: 147 / 464

Interface Access and System Information

System Information

Web: Configuring System Parameters

In the web browser interface, you can enter the following system information:

■

System Name

■

System Location

■

System Contact

For access to the MAC Age Interval and the Time parameters, use the menu
interface or the CLI.

Configure System Parameters in the Web Browser Interface.

1. Click on the

Configuration

tab.

2. Click on

System Info

3. Enter the data you want in the displayed fields.

4. Implement your new data by clicking on

Apply Changes

To access the web-based help provided for the switch, click on

[?]

in the web

browser screen.

7-15

Содержание ProCurve 2610-24
















































































































































































































































































































































































































































































Результаты поиска

Содержание ProCurve 2610-24

Отзывы:

Похожие инструкции для ProCurve 2610-24

Бренды по названию

Популярные бренды

HP ProCurve 2610-24, Руководство по управлению и настройке

Результаты поиска

Содержание ProCurve 2610-24

Отзывы:

Похожие инструкции для ProCurve 2610-24

Бренды по названию

Популярные бренды