HP ProCurve 2610-24 Скачать руководство пользователя страница 399 | Manualshive

Страница: 399 / 464

background image

Troubleshooting

Unusual Network Activity

Filter Traffic.

The IGMP feature does not operate if the switch or VLAN

does not have an IP address configured manually or obtained through DHCP/
Bootp. To verify whether an IP address is configured for the switch or VLAN,
do either of the following:

■

Try Using the Web Browser Interface:

If you can access the web

browser interface, then an IP address is configured.

■

Try To Telnet to the Switch Console:

If you can Telnet to the switch,

then an IP address is configured.

■

Using the Switch Console Interface:

From the Main Menu, check the

Management Address Information screen by clicking on

1. Status and Counters

2. Switch Management Address Information

LACP-Related Problems

Unable to enable LACP on a port with the

interface [e] <

port-number

> lacp

command. In this case, the switch displays the following message:

Operation is not allowed for a trunked port.

You cannot enable LACP on a port while it is configured as a static

Trunk

port.

To enable LACP on a static-trunked port:
first use the

no trunk [e] <

port-number

>

command to disable the static trunk

assignment, and then execute

interface [e] <

port-number

> lacp

.

C a u t i o n

Removing a port from a trunk without first disabling the port can create a
traffic loop that can slow down or halt your network. Before removing a port
from a trunk, ProCurve recommends that you either disable the port or
disconnect it from the LAN.

Port-Based Access Control (802.1X)-Related Problems

N o t e

To list the 802.1X port-access Event Log messages stored on the switch, use

show log 802

.

See also “Radius-Related Problems” on page C-13.

The switch does not receive a response to RADIUS authentication
requests.

In this case, the switch will attempt authentication using the

secondary method configured for the type of access you are using (console,
Telnet, or SSH).

C-9

«
...
397
398
399
400
401
...
»

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

Бренд: Hama Страницы: 5

SuperStack 3 4900

Бренд: 3Com Страницы: 2

Бренд: Datavideo Страницы: 2

PARAGON II Series

Бренд: Raritan Страницы: 1

Paragon Manager

Бренд: Raritan Страницы: 117

Бренд: GBC Страницы: 2

Бренд: TRENDnet Страницы: 11

Бренд: PNI Страницы: 92

Бренд: Lionel Страницы: 8

Бренд: Ubiquiti Страницы: 23

Бренд: Exsys Страницы: 2

Бренд: CGS Instruments Страницы: 39

Бренд: Smartwares Страницы: 2

Бренд: ATEN Страницы: 2

EdgeSwitch 16XP

Бренд: Ubiquiti Страницы: 20

Бренд: SBC Страницы: 28

Бренд: H3C Страницы: 17

Бренд: ATEN Страницы: 303

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды