HP ProCurve 2610-24 Скачать руководство пользователя страница 183

Страница: 183 / 464

Time Protocols

TimeP: Viewing, Selecting, and Configuring

Menu: Viewing and Configuring TimeP

To View, Enable, and Modify the TimeP Protocol:

1. From the Main Menu, select:

2. Switch Configuration...

1. System Information

Time Protocol Selection Parameter

–  TIMEP (the default)
– SNTP
–  None

Figure 9-9. The System Information Screen (Default Values)

2. Press

[E]

(for

Edit

). The cursor moves to the

System Name

field.

3. Use

[v]

to move the cursor to the

Time Sync Method

field.

4. If

TIMEP

is not already selected, use the Space bar to select

TIMEP

, then

press

[v]

once to display and move to the

TimeP Mode

field.

5. Do one of the following:

•

Use the Space bar to select the

DHCP

mode, then press

[v]

to move

the cursor to the

Poll Interval

field, and go to step 6.

9-15

Содержание ProCurve 2610-24
















































































































































































































































































































































































































































































Результаты поиска

Содержание ProCurve 2610-24

Отзывы:

Похожие инструкции для ProCurve 2610-24

Бренды по названию

Популярные бренды

HP ProCurve 2610-24, Руководство по управлению и настройке

Результаты поиска

Содержание ProCurve 2610-24

Отзывы:

Похожие инструкции для ProCurve 2610-24

Бренды по названию

Популярные бренды