HP ProCurve 2610-24 Скачать руководство пользователя страница 159 | Manualshive

Страница: 159 / 464

background image

Configuring IP Addressing

IP Configuration

Configure the Optional Default Gateway.

Using the Global configura

tion level, you can assign one default gateway to the switch.

Syntax

:

ip default-gateway

<ip-address>

For example:

ProCurve(config)# ip default-gateway 10.28.227.115

Note

The switch uses the IP default gateway only while operating as a Layer 2
device. While routing is enabled on the switch, the IP default gateway is not
used. Thus, to avoid loss of Telnet access to off-subnet management stations,
you should use the

ip route

command to configure a static (default) route

before enabling routing. Refer to chapter 16, “IP Routing Features”, for more
information.

Configure Time-To-Live (TTL).

Use this command at the Global config

prompt to set the time that a packet outbound from the switch can exist on
the network. The default setting is 64 seconds.

Syntax

:

ip ttl

<number-of-seconds>

ProCurve(config)# ip ttl 60

In the CLI, you can execute this command only from the global configuration
level. The TTL range is 2 - 255 seconds.

Web: Configuring IP Addressing

You can use the web browser interface to access IP addressing only if the
switch already has an IP address that is reachable through your network.

1. Click on the

Configuration

tab.

2. Click on [

IP Configuration]

.

3. If you need further information on using the web browser interface, click

on

[?]

to access the web-based help available for the Switch 2512/2524.

How IP Addressing Affects Switch Operation

Without an IP address and subnet mask compatible with your network, the
switch can be managed only through a direct terminal device connection to
the Console RS-232 port. You can use direct-connect console access to take
advantage of features that do not depend on IP addressing. However, to realize
the full performance capabilities ProCurve proactive networking offers

8-11

«
...
157
158
159
160
161
...
»

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

Бренд: D-Box Страницы: 27

Бренд: Datavideo Страницы: 4

Бренд: Datavideo Страницы: 66

DXS-3410 Series

Бренд: D-Link Страницы: 54

Бренд: Zektor Страницы: 84

Бренд: Cabletron Systems Страницы: 194

852-1411/000-001

Бренд: WAGO Страницы: 40

SEHI SEHI100TX-

Бренд: Cabletron Systems Страницы: 75

Бренд: Black Box Страницы: 31

Бренд: Black Box Страницы: 76

Бренд: BERNSTEIN Страницы: 38

Бренд: serverLink Страницы: 2

Бренд: Metra Electronics Страницы: 8

Бренд: Edimax Страницы: 8

ConferenceHub TA-6500

Бренд: TeleAdapt Страницы: 16

Бренд: Netis Страницы: 9

BZ-UHD-88M100-ARC

Бренд: BZB Gear Страницы: 42

Бренд: Southern States Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды