HP ProCurve 2610-24 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 464

background image

Selecting a Management Interface

Advantages of Using ProCurve Manager or ProCurve Manager Plus

Extended RMON and sFlow, users can monitor overall traffic levels,
segments with the highest traffic, or even the top users within a
network segment.

•

Group and Policy Management:

Changes in configuration are

tracked and logged, and archived configurations can be applied to one
or many devices. Configurations can be compared over time or
between two devices, with the differences highlighted for users.

•

Advanced VLAN Management:

A new, easy-to-use VLAN manage

ment interface allows users to create and assign VLANs across the
entire network, without having to access each network device indi
vidually.

•

Device Software Updates:

This feature automatically obtains new

device software images from ProCurve and updates devices, allowing
users to download the latest version or choose the desired version.
Updates can be scheduled easily across large groups of devices, all at
user-specified times.

•

Investment Protection:

The modular software architecture of

ProCurve Manager Plus enables ProCurve to offer network adminis
trators add-on software solutions that complement their needs.

2-7

«
...
35
36
37
38
39
...
»

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

SANbox 5600 Series

Бренд: Qlogic Страницы: 408

Бренд: BeeSecure Страницы: 35

Бренд: Attwood Страницы: 2

Бренд: UNICOM Страницы: 1

HYGRASREG KW Series

Бренд: S+S Regeltechnik Страницы: 16

Бренд: Taiden Страницы: 21

Бренд: H3C Страницы: 57

Бренд: Avid Technology Страницы: 34

pro-trim PT1000

Бренд: Seastar Solutions Страницы: 2

Бренд: Jabra Страницы: 13

AVlink VAX-8404F

Бренд: C&C TECHNIC Страницы: 2

ISCOM2600G (A) Series

Бренд: Raisecom Страницы: 96

SecureStack B2 B2G124-48P

Бренд: Enterasys Страницы: 91

IMI SENSORS EX686B77

Бренд: PCB Piezotronics Страницы: 63

Бренд: Zektor Страницы: 30

kontron KSwitch D3 UMP

Бренд: S&T Страницы: 36

IES6300PRO Series

Бренд: 3onedata Страницы: 5

Бренд: Banner Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды