HP ProCurve 2610-24 Скачать руководство пользователя страница 358 | Manualshive

Страница: 358 / 464

background image

File Transfers

Transferring Switch Configurations

Xmodem: Copying a Configuration File from a Serially Connected PC
or Unix Workstation.

To use this method, the switch must be connected via

the serial port to a PC or Unix workstation on which is stored the configuration
file you want to copy. To complete the copying, you will need to know the
name of the file to copy and the drive and directory location of the file.

Syntax

:

copy xmodem startup-config < pc | unix >

For example, to copy a configuration file from a PC serially connected to the
switch:

1. Execute the following command:

2. After you see the above prompt, press

[Enter]

.

3. Execute the terminal emulator commands to begin the file transfer.

4. When the download finishes, you must reboot the switch to implement

the newly downloaded OS. To do so, use one of the following commands:

boot system flash < primary | secondary >

Reboots from the selected flash.

-or

reload

Reboots from the flash image currently in use.

(For more on these commands, refer to “Rebooting the Switch” on page
6-18.)

A-20

«
...
356
357
358
359
360
...
»

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 2

DKVM-16 - KVM Switch

Бренд: D-Link Страницы: 24

Dis-200G Series

Бренд: D-Link Страницы: 161

Dis-200G Series

Бренд: D-Link Страницы: 16

Dis-200G Series

Бренд: D-Link Страницы: 47

Бренд: D-Link Страницы: 25

DGS-3100 SERIES

Бренд: D-Link Страницы: 54

DGS-3100 SERIES

Бренд: D-Link Страницы: 220

Бренд: D-Link Страницы: 24

DGS-1248T - Switch

Бренд: D-Link Страницы: 52

DGS-1216T - Switch

Бренд: D-Link Страницы: 42

DGS-1216T - Switch

Бренд: D-Link Страницы: 10

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 379

Бренд: D-Link Страницы: 240

Бренд: D-Link Страницы: 188

DES-3326S - Switch - Stackable

Бренд: D-Link Страницы: 349

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды