HP ProCurve 2610-24 Скачать руководство пользователя страница 82

Страница: 82 / 464

Using the Web Browser Interface

Support/Mgmt URLs Feature

The Support/Mgmt URLs window enables you to change the World Wide Web
Universal Resource Locator (URL) for two functions:

■

Support URL

– a support information site for your switch

■

Management Server URL

– The web site for web browser online Help.

The default is:

www.hp.com/rnd/device_help

3. Enter one of the following (or use the default setting):

– The URL for the support information source you want the

switch to access when you click on the web browser interface
Support tab. The default is the URL for the ProCurve
Networking home page.

– The URL of a PCM (ProCurve Network Manager) workstation

or other server for the online Help files for this web browser
interface.

1. Click Here

2. Click Here

4. Click on Apply Changes

Figure 5-6. The Default Support/Mgmt URLs Window

5-12

Содержание ProCurve 2610-24
















































































































































































































































































































































































































































































Результаты поиска

Содержание ProCurve 2610-24

Отзывы:

Похожие инструкции для ProCurve 2610-24

Бренды по названию

Популярные бренды

HP ProCurve 2610-24, Руководство по управлению и настройке

Результаты поиска

Содержание ProCurve 2610-24

Отзывы:

Похожие инструкции для ProCurve 2610-24

Бренды по названию

Популярные бренды