HP ProCurve 2610-24 Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 464

background image

Switch Memory and Configuration

Using Primary and Secondary Flash Image Options

Operating Notes

Default Boot Source.

The switch reboots from primary flash by default

unless you specify the secondary flash.

Boot Attempts from an Empty Flash Location.

In this case, the switch

aborts the attempt and displays

Image does not exist

Operation aborted.

Interaction of Primary and Secondary Flash Images with the Current
Configuration.

The switch has one startup-config file (page 6-3), which it

always uses for reboots, regardless of whether the reboot is from primary or
secondary flash. Also, for rebooting purposes, it is not necessary for the
software image and the startup-config file to support identical software fea
tures. For example, suppose you have just downloaded a software upgrade
that includes new features that are not supported in the software you used to
create the current startup-config file. In this case, the software simply assigns
factory-default values to the parameters controlling the new features. Simi
larly, If you create a startup-config file while using a version “Y” of the switch
software, and then reboot the switch with an earlier software version “X” that
does not include all of the features found in “Y”, the software simply ignores
the parameters for any features that it does not support.

6-22

«
...
114
115
116
117
118
...
»

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

COOPER POWER SERIES

Бренд: Eaton Страницы: 32

Бренд: Keithley Страницы: 452

Бренд: Attwood Страницы: 2

Бренд: WoMaster Страницы: 2

MatrixPRO 8x8 DVI

Бренд: Barco Страницы: 2

Nexoos 370 Series

Бренд: Soyntec Страницы: 7

MCD-LED17 series

Бренд: Raritan Страницы: 89

Бренд: Avenview Страницы: 10

Бренд: Orno Страницы: 2

IES6200-PN-16T4GS-2P48

Бренд: 3onedata Страницы: 3

Smart Switch 2:1

Бренд: XTBA Страницы: 3

Бренд: Campbell Hausfeld Страницы: 4

Бренд: Lakeshore Страницы: 82

Бренд: I-Tech Страницы: 19

Бренд: Linkskey Страницы: 2

Бренд: Unipoe Страницы: 9

Бренд: Cabletron Systems Страницы: 116

Genesis Digital HSM-04-02

Бренд: Hall Research Technologies Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды