HP ProCurve 2610-24 Скачать руководство пользователя страница 416

Страница: 416 / 464

Troubleshooting

Using Logging To Identify Problem Sources

Debug Types

This section describes the types of debug messages the switch can send to
configured debug destinations.

Syntax:

[no] debug < debug-type >

all

Configures the switch to send all debug types to the config
ured debug destination(s). (Default: Disabled)

event

Configures the switch to send Event Log messages to the
configured debug destination(s).

Note:

This has no effect

on event notification messages the switch routinely sends
to the Event Log itself. Also, this debug type is automatically
enabled in these cases:

• If there is currently no Syslog server address configured

and you use

logging <

ip-addr

to configure an address.

• If there is currently at least one Syslog server address

configured and the switch is rebooted or reset.

(Default: Disabled)

dhcp-snooping

Assigns DHCP snooping debug messages to the debug des
tination

lldp

Assigns LLDP debug messages to the debug destination.

C-26

Содержание ProCurve 2610-24
















































































































































































































































































































































































































































































Результаты поиска

Содержание ProCurve 2610-24

Отзывы:

Похожие инструкции для ProCurve 2610-24

Бренды по названию

Популярные бренды

HP ProCurve 2610-24, Руководство по управлению и настройке

Результаты поиска

Содержание ProCurve 2610-24

Отзывы:

Похожие инструкции для ProCurve 2610-24

Бренды по названию

Популярные бренды