HP ProCurve 2610-24 Скачать руководство пользователя страница 123 | Manualshive

Страница: 123 / 464

background image

Switch Memory and Configuration

Multiple Configuration Files

pressing the Reset button or to a power cycle always uses the software version
in primary flash, the operator needs to configure the switch to always boot
from primary flash with the startup-config file named

minconfig

(in memory

slot 1). Also, whenever the switch boots from secondary flash, the operator
also wants the startup-config named

newconfig

to be used. The following two

commands configure the desired behavior.

ProCurve(config)# startup-default pri config minconfig

ProCurve(config) # startup-default sec config newconfig.

Overriding the Default Reboot Configuration Policy.

This command

provides a method for manually rebooting with a specific startup-config file
other than the file specified in the default reboot configuration policy.

Syntax:

boot system flash < primary | secondary > config <

filename

>

Specifies the name of the startup-config file to apply for the
immediate boot instance only. This command overrides the
current reboot policy.

Using Reload To Reboot From the Current Flash Image and Startup-
Config File.

Syntax:

[no] reload [after <[dd:]hh:]mm> | at <hh:mm[:ss]> [<mm/dd[/[yy]yy]>]]

Enables a scheduled warm reboot of the switch. The switch boots
up with the same startup config file and using the same flash
image as before the reload.

Caution:

When using redundant management, the

reload at/after

command causes a switchover at the scheduled time to the other
management module, which may not be running the same soft
ware image or have the same configurations.
Parameters include:

•

after:

Schedules a warm reboot of the switch after a given

amount of time has passed.

•

at:

Schedules a warm reboot of the switch at a given time.

The

no

form of the command removes a pending reboot request.

For more details and examples, see below.

6-29

«
...
121
122
123
124
125
...
»

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

Бренд: Dataprobe Страницы: 31

Бренд: IBM Страницы: 13

Flex System EN2092

Бренд: IBM Страницы: 2

LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES

Бренд: Jabra Страницы: 4

Бренд: LevelOne Страницы: 17

Бренд: N-Tron Страницы: 196

Бренд: Steren Страницы: 13

Бренд: KYLAND Страницы: 34

Бренд: TRENDnet Страницы: 2

Бренд: Kramer Страницы: 11

Бренд: IPGARD Страницы: 2

Бренд: DELTA DORE Страницы: 3

GTB-MHDMI1.3-442

Бренд: Gefen Страницы: 29

Бренд: Linksys Страницы: 22

Бренд: Murphy Страницы: 24

Бренд: Led Control Страницы: 22

Бренд: Mengual Страницы: 2

Бренд: xpr Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды