HP ProCurve 2610-24 Скачать руководство пользователя страница 310 | Manualshive

Страница: 310 / 464

background image

Configuring for Network Management Applications

LLDP (Link-Layer Discovery Protocol)

Also, by using

show

commands to access the switch’s neighbor database for

information collected by an individual switch, system administrators can learn
about other devices connected to the switch, including device type
(capability) and some configuration information.

LLDP Terminology

Adjacent Device:

Refer to “Neighbor or Neighbor Device”.

Advertisement:

See LLDPDU.

Active Port:

A port linked to another active device (regardless of whether

STP is blocking the link).

LLDP:

Link Layer Discovery Protocol. ProCurve switches are compatible

with IEEE 802.1AB-2005.

LLDP-Aware:

A device that has LLDP in its operating code, regardless of

whether LLDP is enabled or disabled.

LLDP Device:

A switch, server, router, or other device running LLDP.

LLDP Neighbor:

An LLDP device that is either directly connected to another

LLDP device or connected to that device by another, non-LLDP Layer 2 device
(such as a hub) Note that an 802.1D-compliant switch does not forward LLDP
data packets even if it is not LLDP-aware.

LLDPDU (LLDP Data Unit):

LLDP data packets are transmitted on active

links and include multiple TLVs containing global and per-port switch
information. In this guide, LLDPDUs are termed “advertisements” or
“packets”.

MIB

(Management Information Base): An internal database the switch

maintains for configuration and performance information.

Neighbor:

See “LLDP Neighbor”.

Non_LLDP Device:

A device that is not capable of LLDP operation.

TLV (Type-Length-Value):

A data unit that includes a data type field, a data

unit length field (in bytes), and a field containing the actual data the unit is
designed to carry (as an alphanumeric string, a bitmap, or a subgroup of
information). Some TLVs include subelements that occur as separate data
points in displays of information maintained by the switch for LLDP
advertisements. (That is, some TLVs include multiple data points or
subelements.)

13-30

«
...
308
309
310
311
312
...
»

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

Бренд: Patton electronics Страницы: 104

Бренд: Intermatic Страницы: 1

VEEMUX SM-nXm-15V-LC

Бренд: Network Technologies Страницы: 46

PU-8H8HBTPL-4K22

Бренд: CYP Страницы: 24

S3100-SI Series

Бренд: H3C Страницы: 58

Бренд: Xantech Страницы: 4

Бренд: Lindy Страницы: 2

Бренд: Extron electronics Страницы: 137

Бренд: Topex Страницы: 170

StorageWorks SAN Switch Integrated/32

Бренд: Compaq Страницы: 104

Crocodile Tail Loop

Бренд: One Control Страницы: 9

Бренд: UNICOM Страницы: 15

KingShield T206-C

Бренд: Green Brook Страницы: 2

Бренд: ATEN Страницы: 4

Бренд: Edge-Core Страницы: 65

ADDERView Secure AVS-4128

Бренд: ADDER Страницы: 24

Бренд: I-Tech Страницы: 19

Бренд: Linkskey Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды