HP ProCurve 2610-24 Скачать руководство пользователя страница 261 | Manualshive

Страница: 261 / 464

background image

Port Trunking

Port Status and Configuration

Table 12-1. Trunk Types Used in Static and Dynamic Trunk Groups

Trunking Method

LACP

Trunk

Dynamic

Yes

No

Static

Yes

Yes

Table 12-2. Trunk Configuration Protocols

Protocol

Trunking Options

LACP

Provides dynamic and static LACP trunking options.

(802.3ad)

•

Dynamic LACP —

Use the switch-negotiated dynamic LACP trunk when:

– The port on the other end of the trunk link is configured for Active or Passive LACP.
– You want to achieve fault-tolerance for high-availability applications where you want up to an eight-

link trunk with one or more standby links available in case an active link goes down. (Both ends of the
link must be dynamic LACP.)

•

Static LACP —

Use the manually configured static LACP trunk when:

–   The port on the other end of the trunk link is configured for a static LACP trunk
–   You want to configure non-default spanning tree (STP) or IGMP parameters on an LACP trunk group.
–   You want an LACP trunk group to operate in a VLAN other than the default VLAN and GVRP is disabled.

(Refer to “VLANs and Dynamic LACP” on page 12-20.)

– You want to use a monitor port on the switch to monitor an LACP trunk.

See “Trunk Group Operation Using LACP” on page 12-15.

Trunk

Provides manually configured, static-only trunking to:

(non-

• Most ProCurve switches and routing switches not running the 802.3ad LACP protocol.

protocol)

• Windows NT and HP-UX workstations and servers
Use the Trunk option when:

– The device to which you want to create a trunk link is using a non-802.3ad trunking protocol
– You are unsure which type of trunk to use, or the device to which you want to create a trunk link is

using an unknown trunking protocol.

– You want to use a monitor port on the switch to monitor traffic on a trunk.

Refer to “Trunk Group Operation Using the “Trunk” Option” on page 12-21.

12-5

«
...
259
260
261
262
263
...
»

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

Бренд: TAMS Страницы: 28

Бренд: 3Com Страницы: 2

CoreBuilder 5000

Бренд: 3Com Страницы: 16

CoreBuilder 9000

Бренд: 3Com Страницы: 24

Бренд: eao Страницы: 2

Бренд: eao Страницы: 2

Бренд: echoflex Страницы: 8

Бренд: United Electric Controls Страницы: 6

Бренд: PRO SIGNAL Страницы: 5

DMS-1250 Series

Бренд: D-Link Страницы: 38

Бренд: Audio Authority Страницы: 12

EX ZS 92 S 22 VD F

Бренд: steute Страницы: 28

Бренд: LONG-JOIN Страницы: 2

Бренд: Cudy Страницы: 2

Бренд: Waters Network Systems Страницы: 12

2X2 VGA SWITCHER

Бренд: Gefen Страницы: 12

Edison Cooper Power Series

Бренд: Eaton Страницы: 12

Бренд: Manhattan Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды