HP ProCurve 2610-24 Скачать руководство пользователя страница 337

Страница: 337 / 464

Configuring for Network Management Applications

LLDP (Link-Layer Discovery Protocol)

The following example shows the default CDP configuration.

CDP Enable/Disable on the Switch

Per-Port CDP Enable/Disable

Figure 13-24. Example of Show CDP with the Default CDP Configuration

Viewing the Switch’s Current CDP Neighbors Table.

Devices are listed

by the port on which they were detected.

Syntax:

show cdp neighbors

Lists the neighboring CDP devices the switch detects,
with a subset of the information collected from the
device’s CDP packet.

[ [e] port-numb [detail] ]

Lists the CDP device connected to the specified port.
(Allows only one port at a time.) Using

detail

provides

a longer list of details on the CDP device the switch
detects on the specified port.

[detail [ [e] port-num ] ]

Provides a list of the details for all of the CDP devices
the switch detects. Using

port-num

produces a list of

details for the selected port.

Figure 13-25 lists two CDP devices that the switch has detected by receiving
their CDP packets.

Figure 13-25. Example of CDP Neighbors Table Listing

13-57

Содержание ProCurve 2610-24
















































































































































































































































































































































































































































































Результаты поиска

Содержание ProCurve 2610-24

Отзывы:

Похожие инструкции для ProCurve 2610-24

Бренды по названию

Популярные бренды

HP ProCurve 2610-24, Руководство по управлению и настройке

Результаты поиска

Содержание ProCurve 2610-24

Отзывы:

Похожие инструкции для ProCurve 2610-24

Бренды по названию

Популярные бренды