HP ProCurve 2610-24 Скачать руководство пользователя страница 341 | Manualshive

Страница: 341 / 464

background image

File Transfers

Downloading Switch Software

General Switch Software Download Rules

■

A switch software image downloaded through the menu interface always
goes to primary flash.

■

After a switch software download, you must reboot the switch to imple
ment the newly downloaded code. Until a reboot occurs, the switch
continues to run on the software it was using before the download started.

N o t e

Downloading new switch software does not change the current switch con
figuration. The switch configuration is contained in separate files that can also
be transferred. Refer to “Transferring Switch Configurations” on page A-18.

In most cases, if a power failure or other cause interrupts a flash image
download, the switch reboots with the image previously stored in primary
flash. In the unlikely event that the primary image is corrupted (which may
occur if a download is interrupted by a power failure), the switch goes into
boot ROM mode. In this case, use the boot ROM console to download a new
switch software image to primary flash. Refer to “Restoring a Flash Image” on
page C-45.

Using TFTP To Download Switch Software from a
Server

This procedure assumes that:

■

An switch software file for the switch has been stored on a TFTP server
accessible to the switch. (The switch software file is typically available
from the ProCurve website at

www.procurve.com

.)

■

The switch is properly connected to your network and has already been
configured with a compatible IP address and subnet mask.

■

The TFTP server is accessible to the switch through IP.

Before you use the procedure, do the following:

■

Obtain the IP address of the TFTP server in which the switch software file
has been stored.

■

If VLANs are configured on the switch, determine the name of the VLAN
in which the TFTP server is operating.

■

Determine the name of the switch software file stored in the TFTP server
for the switch (for example,

G0721.swi

).

A-3

«
...
339
340
341
342
343
...
»

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

Бренд: D-Link Страницы: 2

Бренд: N-Tron Страницы: 2

Бренд: Vector Страницы: 6

Бренд: Touch-plate Страницы: 12

EXHL-TRN-LE1 Series

Бренд: Larson Electronics Страницы: 2

SISTG1040-242-LRT

Бренд: Transition Networks Страницы: 31

Бренд: I-Tech Страницы: 29

Бренд: Cabletron Systems Страницы: 110

Mini Hub 5 port

Бренд: Sandberg Страницы: 12

Evolution EVMX4442

Бренд: Vanco Страницы: 12

Бренд: Eaton Страницы: 12

ScatterBox POE308

Бренд: System Q Страницы: 2

D-PFS3110-8ET1GT1GF-96

Бренд: Dahua Страницы: 17

Бренд: Ocean Matrix Страницы: 6

Бренд: Kramer Страницы: 8

Бренд: QSFPTEK Страницы: 11

Бренд: Novus Страницы: 24

Бренд: N-Tron Страницы: 152

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды