HP ProCurve 2610-24 Скачать руководство пользователя страница 396 | Manualshive

Страница: 396 / 464

background image

Troubleshooting

Browser or Telnet Access Problems

Cannot Telnet into the switch console from a station on the network:

■

Telnet access may be disabled by the

Inbound Telnet Enabled

parameter in

the System Information screen of the menu interface:

2. Switch Configuration

1. System Information

■

The switch may not have the correct IP address, subnet mask, or gateway.
Verify by connecting a console to the switch’s Console port and selecting:

2. Switch Configuration

5. IP Configuration

Note:

If DHCP/Bootp is used to configure the switch, see the

Note

, above.

■

If you are using DHCP to acquire the IP address for the switch, the IP
address “lease time” may have expired so that the IP address has changed.
For more information on how to “reserve” an IP address, refer to the
documentation for the DHCP application that you are using.

■

If one or more IP-Authorized managers are configured, the switch allows
inbound telnet access only to a device having an authorized IP address.
For more information on IP Authorized managers, see the

Access Security

Guide

for your switch.

C-6

«
...
394
395
396
397
398
...
»

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

Бренд: D-Link Страницы: 36

GuardSwitch 300 Series

Бренд: GE Страницы: 4

Бренд: Perel Страницы: 4

Бренд: ADDER Страницы: 46

Бренд: Digitronic Страницы: 24

Бренд: G-Lab Страницы: 12

Бренд: CIECO Страницы: 17

Бренд: IPGARD Страницы: 2

Бренд: Enterasys Страницы: 41

Бренд: Hama Страницы: 14

Бренд: SMART-AVI Страницы: 9

Gigabit Switch 8

Бренд: 3Com Страницы: 2

Бренд: Shadow Страницы: 4

B-520-MTRX-230-6x4+2

Бренд: Binary Страницы: 32

Alduti-Rupter Switches Outdoor Distribution

Бренд: S&C Страницы: 26

Бренд: IDK Страницы: 81

950-2080 NEW STYLE GAS PRESSURE SWITCH

Бренд: TJERNLUND Страницы: 1

Бренд: SC&T Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды