manualshive.com logo in svg

HP ProCurve 2610-24, Руководство по управлению и настройке

HP ProCurve 2610-24 - сетевой коммутатор с широким функционалом и возможностями для настройки и управления сетью. Управляйте устройством с помощью Management And Configuration Manual, которое можно бесплатно скачать на manualshive.com. Идеальный выбор для оптимизации работы вашей сети.

Поделиться
Скачать
background image

Troubleshooting 

Using Logging To Identify Problem Sources 

Syntax

: 

show debug 

List the current debug status for both Syslog logging and 
Session logging. 

Shows that Syslog logging is enabled 
and sending event messages to the 

user 

facility on the SyslogD server at IP 
address 18.120.38.155. 

Shows that session logging is operating 
through another session. (You can take 
control of session logging by executing 

debug destination session

 in the 

session you are currently using.) 

Figure C-12. Example of Show Debug Status 

■

  

Rebooting the Switch or pressing the Reset button resets the 
Debug Configuration. 

Debug Option 

Effect of a Reboot or Reset 

logging (destination)   If any SyslogD server IP addresses are in the startup-config file, 

they are saved across a reboot and the logging destination 
option remains enabled. Otherwise, the logging destination is 
disabled. 

Session (destination)   Disabled. 

All (event type)  

Disabled. 

Event (event type)   

If a Syslog server is configured in the startup-config file, resets 
to enabled, regardless of prior setting. Disabled if no Syslog 
server is configured. 

■

  

Debug commands do not affect message output to the Event Log. 

As a separate option, invoking debug with the 

event

 option causes the 

switch to send Event Log messages to whatever debug destination(s) you 
configure (session and/or logging), as well as to the Event Log. 

■

  

Ensure that your Syslog server(s) will accept Debug messages.

 All 

Syslog messages the switch generates carry the configured facility. All 
Syslog messages resulting from debug operation carry a “debug” severity. 
If you configure the switch to transmit debug messages to a SyslogD 

C-31 

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

3Com 4210 Series Datasheet preview
4210 Series
Бренд: 3Com Страницы: 8
3Com PathBuilder S200 Series Feature Manual preview
PathBuilder S200 Series
Бренд: 3Com Страницы: 11
3Com 4400 Datasheet preview
4400
Бренд: 3Com Страницы: 8
3Com CoreBuilder 3500 Getting Started Manual preview
CoreBuilder 3500
Бренд: 3Com Страницы: 96
IDEC HS5L Series Instruction Sheet preview
HS5L Series
Бренд: IDEC Страницы: 8
IDEM SAFETY SWITCHES MPR Operating Instructions preview
MPR
Бренд: IDEM SAFETY SWITCHES Страницы: 2
Quintum Tenor AXE1600 Specifications preview
Tenor AXE1600
Бренд: Quintum Страницы: 2
Gefen EXT-DVI-441DL User Manual preview
EXT-DVI-441DL
Бренд: Gefen Страницы: 31
ORiNG IGS-1082GP Quick Installation Manual preview
IGS-1082GP
Бренд: ORiNG Страницы: 2
Theben TIMEGUARD WF10COM Installation & Operating Instructions Manual preview
TIMEGUARD WF10COM
Бренд: Theben Страницы: 35
Data EOC Master CD7944N Product User Manual preview
EOC Master CD7944N
Бренд: Data Страницы: 18
Kobold PPS-1201 Operating Instructions Manual preview
PPS-1201
Бренд: Kobold Страницы: 10
ATEN KVMP CS1782A Quick Start Manual preview
KVMP CS1782A
Бренд: ATEN Страницы: 2
Hisselektronik Safeline 2000 Light Manual For Programmering preview
Safeline 2000 Light
Бренд: Hisselektronik Страницы: 9
Jabra EHS - Brochure preview
EHS -
Бренд: Jabra Страницы: 13
QNAP QSW-M2108 Series Quick Installation Manual preview
QSW-M2108 Series
Бренд: QNAP Страницы: 28
Extron electronics CrossPoint 42 HVA User Manual preview
CrossPoint 42 HVA
Бренд: Extron electronics Страницы: 46
Kramer VP-553xl User Manual preview
VP-553xl
Бренд: Kramer Страницы: 85

Бренды по названию

Популярные бренды

Загрузить еще бренды