manualshive.com logo in svg

HP ProCurve 2610-24, Руководство по управлению и настройке

HP ProCurve 2610-24 - сетевой коммутатор с широким функционалом и возможностями для настройки и управления сетью. Управляйте устройством с помощью Management And Configuration Manual, которое можно бесплатно скачать на manualshive.com. Идеальный выбор для оптимизации работы вашей сети.

Поделиться
Скачать
background image

Switch Memory and Configuration 

Using Primary and Secondary Flash Image Options 

Table 6-2. 

Comparing the Boot and Reload Commands 

Actions 

Included In 
Boot? 

Included In Reload 

Note 

Save all 

Optional, 

Optional with reload 

Config changes saved to 

configuration 
changes since the 
last boot or reload 

with prompt 

<cr>, when prompt 
displays. 
Not saved with 

reload 

at/after 

commands; No 

prompt is displayed. 

the startup-config file if 
“y” is selected (

reload 

command). 

Perform all system 
self-tests 

Yes 

No 

The 

reload

 command 

provides a faster system 
reboot. 

Choice of primary or 
secondary flash 
image 

Yes 

No—Uses the current 
flash image. 

Perform a scheduled 
reboot 

No 

Yes 

Use the 

reload

 command 

with after/at parameters 
(see page 6-29 for details). 

Booting from Primary Flash.  

This command always boots the switch from 

primary flash, and executes the complete set of subsystem self-tests. 

Syntax

: 

boot 

For example, to boot the switch from primary flash with pending configuration 
changes in the running-config file: 

Figure 6-13.  Example of Boot Command (Default Primary Flash) 

In the above example, typing either a 

y

 or 

n

 at the second prompt initiates the 

reboot operation. Also, if there are no pending configuration changes in the 
running-config file, then the reboot commences without the pause to display 

Boot from primary flash

. 

Booting from a Specified Flash. 

This version of the boot command gives 

you the option of specifying whether to reboot from primary or secondary 
flash, and is the required command for rebooting from secondary flash. This 
option also executes the complete set of subsystem self-tests. 

6-19 

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

Datavideo SE-3000 Instruction Manual preview
SE-3000
Бренд: Datavideo Страницы: 58
KanexPro MX-HDBT8X818G Manual preview
MX-HDBT8X818G
Бренд: KanexPro Страницы: 16
Kathrein EXE 159 Manual preview
EXE 159
Бренд: Kathrein Страницы: 41
Xantech AC1 Installation Instructions preview
AC1
Бренд: Xantech Страницы: 2
National Instruments SCXI-1175 Getting Started Manual preview
SCXI-1175
Бренд: National Instruments Страницы: 23
Videosec PS04PGE+1PD User Manual preview
PS04PGE+1PD
Бренд: Videosec Страницы: 5
Cabletron Systems SmartSTACK 100 ELS100-16TX Getting Started preview
SmartSTACK 100 ELS100-16TX
Бренд: Cabletron Systems Страницы: 16
Omega OM-ESW-105-POE User Manual preview
OM-ESW-105-POE
Бренд: Omega Страницы: 17
Gefen EXT-HDMI-CAT5-844 User Manual preview
EXT-HDMI-CAT5-844
Бренд: Gefen Страницы: 28
Edimax ER-5397P User Manual preview
ER-5397P
Бренд: Edimax Страницы: 8
TRENDnet TK-423K - USB/PS/2 KVM Switch Quick Installation Manual preview
TK-423K - USB/PS/2 KVM Switch
Бренд: TRENDnet Страницы: 14
Brightlink BL-4X4-HDBT Operating Instructions Manual preview
BL-4X4-HDBT
Бренд: Brightlink Страницы: 17
Veris Industries Hawkeye H950 Installation Manual preview
Hawkeye H950
Бренд: Veris Industries Страницы: 2
IOGear CS1222TAA4 Manual preview
CS1222TAA4
Бренд: IOGear Страницы: 54
MicroNet SP684C User Manual preview
SP684C
Бренд: MicroNet Страницы: 74
Taiden HCS-4310M User Manual preview
HCS-4310M
Бренд: Taiden Страницы: 4
LogiLink HD0006 Specifications preview
HD0006
Бренд: LogiLink Страницы: 3
Wantec 2wIP-E-S-TW Installation Manual preview
2wIP-E-S-TW
Бренд: Wantec Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды