HP ProCurve 2610-24 Скачать руководство пользователя страница 296 | Manualshive

Страница: 296 / 464

background image

Configuring for Network Management Applications

Using SNMP Tools To Manage the Switch

CLI: Viewing and Configuring SNMP Community Names

Community Name Commands

Page

show snmp-server [<community-string>]

13-16

[no] snmp-server

13-17

[community <community-str>]

13-17

[host <community-str> <ip-addr>]

13-21

[<none | debug | all | not-info | critical>]

[enable traps <authentication>

13-25

Listing Community Names and Values.

This command lists the data for

currently configured SNMP community names (along with trap receivers and
the setting for authentication traps — see “SNMP Notification and Traps” on
page 13-18).

Syntax

:

show snmp-server [<community-string>]

This example lists the data for all communities in a switch; that is, both the
default ProCurve "public" community name and another community named
"blue-team".

Default
Community and
Settings

Non-Default
Community and
Settings

Trap Receiver
Data (See page
13-18.)

Figure 13-7. Example of the SNMP Community Listing with Two Communities

To list the data for only one community, such as the "public" community, use
the above command with the community name included. For example:

ProCurve# show snmp-server public

13-16

«
...
294
295
296
297
298
...
»

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

Бренд: Under Control Страницы: 9

SwitchMan USB-Combo SW2

Бренд: Raritan Страницы: 2

Бренд: KinAn Страницы: 4

Бренд: Lindy Страницы: 54

Бренд: Opengear Страницы: 109

Бренд: Black Box Страницы: 50

SECURVIEW SV-7020

Бренд: CrimeStopper Страницы: 1

GSM7352S - ProSafe Switch - Stackable

Бренд: NETGEAR Страницы: 628

Бренд: Novatek-electro Страницы: 8

Бренд: SyncAV Страницы: 2

Бренд: Dahua Страницы: 17

Бренд: CYP Страницы: 16

Бренд: Honeywell Страницы: 11

Бренд: Honeywell Страницы: 6

Бренд: Honeywell Страницы: 8

Ademco VistaView-100

Бренд: Honeywell Страницы: 4

Бренд: Honeywell Страницы: 4

Бренд: Honeywell Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды