background image

        

       

WARNING

PERSONAL INJURY

DO NOT USE these products as safety or emergency stop 
devices or in any other application where failure of the product 
could result in personal injury.

Failure to comply with these instructions could result in 
death or serious injury.

 Installation Instructions for the

Enclosed Basic Series Limit Switches

Sensing and Control

Issue 5

88173

GENERAL INFORMATION

•  Honeywell’s Enclosed Basic Series of Limit Switches are 

usable in many applications. The wide variety of actuators 
offered and their robust diecast housing make them ideal for 
applications that require reliable switching and performance. 
There are several styles of enclosed basic switches, includ-
ing side and flange mounting switches as well high capacity 
and double pole type. 

•  Refer to switch labeling for applicable electrical ratings and 

certifications

•  For technical product support, engineering drawings, 

technical data, and additional information for products from 

Honeywell’s Enclosed Basic Series of Limit Switches please 

visit sensing.honeywell.com, or call the support numbers on 
the last page of this document.  

MOUNTING

1.  Mount switches on flat, rigid surface.

E6 Side Mounting Pattern

 25,4 mm

[1.00 in]

2X CLEARANCE HOLE FOR #6 

MOUNTING SCREW*

E6 SIDE MOUNTING

V6 Flange Mounting Pattern

41,6 mm

1.63 in

 

2X  Ø 4,3 mm [0.17 in] MOUNTING HOLES

V6 FLANGE MOUNTING

G1 Side Mounting Pattern

 31,0 mm

   [1.22 in]

 75,0 mm

[2.95 in]

2X  Ø 5,5 mm [0.216 in] MOUNTING HOLES

G1 SIDE MOUNTING

H1 Flange Mounting Pattern

41,9 mm

1.65 in

2X  Ø 0.22 5,5 mm [0.22 in] 

MOUNTING HOLES

H1 FLANGE MOUNTING

2.  Boot-sealed and side-mounting switches use sealing wash

-

ers under screw heads on the sides between switch and 
mounting surface on other side to maintain seal.

3.  Unsealed, side mounting switches: Use lockwashers under 

screw heads on one side; under nut on other side.

4.  Connect conduit to conduit opening. Apply conduit sealing if 

required by application.

INSTALLATION TIPS

1. 

Do not lubricate any internal part of the switch. 

The inter-

nal switch does not require any additional lubrication

2.  When installing the switch, ensure 

that it is not the low 

point in the conduit run

. Doing so will ensure that con-

densation created in the conduit will not flow into the switch 
housing.

3. 

Do not enlarge the mounting holes on side mounting 
switch

. Doing so will compromise the internal switching ele-

ment’s seal integrity. 

Содержание 88173







Отзывы: