HP ProCurve 2610-24 Скачать руководство пользователя страница 200

Страница: 200 / 464

Port Status and Basic Configuration

Viewing Port Status and Configuring Port Parameters

Figure 10-2. Example of Port/Trunk Settings with a Trunk Group Configured

2. Press

[E]

(for

Edit

). The cursor moves to the

Enabled

field for the first port.

3. Refer to the online help provided with this screen for further information

on configuration options for these features.

4. When you have finished making changes to the above parameters, press

[Enter]

, then press

[S]

(for

Save

CLI: Viewing Port Status and Configuring Port
Parameters

Port Status and Configuration Commands

show interfaces brief

below

show interfaces config

page 10-9

interface

page 10-10

show spanning tree

page 10-10

show tech transceivers

page 10-15

From the CLI, you can configure and view all port parameter settings and view
all port status indicators.

Using the CLI To View Port Status

Use the following commands to display port status and configuration:

■

show interfaces brief

: Lists the full status and configuration for all ports

on the switch.

10-8

Содержание ProCurve 2610-24
















































































































































































































































































































































































































































































Результаты поиска

Содержание ProCurve 2610-24

Отзывы:

Похожие инструкции для ProCurve 2610-24

Бренды по названию

Популярные бренды

HP ProCurve 2610-24, Руководство по управлению и настройке

Результаты поиска

Содержание ProCurve 2610-24

Отзывы:

Похожие инструкции для ProCurve 2610-24

Бренды по названию

Популярные бренды