HP ProCurve 2610-24 Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 464

background image

Switch Memory and Configuration

Using the Menu and Web Browser Interfaces To Implement Configuration Changes

How To Reset the startup-config and running-config Files to the
Factory-Default Configuration.

This command reboots the switch,

replacing the contents of the current startup-config and running-config files
with the factory-default startup configuration.

Syntax

:

erase startup-config

For example:

ProCurve(config)# erase startup-config

Configuration will be deleted and device rebooted, continue [y/n]?

Figure 6-3.Resetting to the Factory-Default Configuration

Press

[Y]

to replace the current configuration with the factory default config

uration and reboot the switch. Press

[N]

to retain the current configuration and

prevent a reboot.

Using the Menu and Web Browser
Interfaces To Implement
Configuration Changes

The menu and web browser interfaces offer these advantages:

■

Quick, easy menu or window access to a subset of switch configuration
features (See the “Menu Features List” on page 3-14 and the web browser
“General Features” list on page.)

■

Viewing several related configuration parameters in the same screen, with
their default and current settings

■

Immediately changing both the running-config file and the startup-config
file with a single command

Configuration Changes Using the Menu Interface

You can use the menu interface to simultaneously save and implement a
subset of switch configuration changes without having to reboot the switch.
That is, when you save a configuration change in the menu interface, you
simultaneously change both the running-config file and the startup-config file.

6-9

«
...
101
102
103
104
105
...
»

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

Бренд: SIMON RWA Страницы: 3

MicroHub GUH274W3

Бренд: IOGear Страницы: 1

Бренд: Accton Technology Страницы: 547

Бренд: Optex Страницы: 2

Бренд: Hall Research Technologies Страницы: 9

Бренд: Wetekom Страницы: 34

Бренд: Kramer Страницы: 4

CTRLink EISK8P-GT

Бренд: Contemporary Controls Страницы: 4

SRW224 - 10/100 - Gigabit Switch

Бренд: Linksys Страницы: 2

Бренд: GenerLink Страницы: 16

Бренд: Magnetrol Страницы: 32

Desktop KVM Switch

Бренд: Equip Страницы: 10

Бренд: Pulsar Страницы: 8

NXT Switch 195A

Бренд: LightPro Страницы: 12

60-774 - Security SuperBus 2000 8-Zone Input Module

Бренд: ITI Страницы: 8

Бренд: Metel Страницы: 11

UltraConsole Remote UCR-1R1X04U

Бренд: Rose electronics Страницы: 2

UltraConsole UC1-1X16U

Бренд: Rose electronics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды